Search Results

Previous View PDF Catalogue Regulators Air Filters / Regulators RTLP Regulators with Quick Fittings Push Lock type New Regulators with Quick Fittings are available! Next SIMILAR PRODUCTS Air Filters / Regulators Regulators RN100-111 RDN100-111 Compact, lightweight regulator. Quick fitting for simple tube connection to the device. Small FR series Regulators RN100-111 Small FR series Regulators RN100-111 Air pressure can be controlled by electrical signals. P.W.M. control poppet type main unit structure enables non-bleeding. Supports easy air quality management and reliability, and long life. Electro Pneumatic Transducing Regulator ETR Electro Pneumatic Transducing Regulator ETR Perfect for pressure control of solvents used in liquid crystal and semiconductor processes, carrier gas in a pure water circuit, clean air, and gas, as well as other non-grease and non-oil essential lines. Stainless steel Regulator RS Stainless steel Regulator RS Compact yet with a stable pressure regulator with preset markers included as standard. Select from among standard pressure specification, integrated check mechanism, low-pressure specification. Multi series Regulators R150-602 Multi series Regulators R150-602 (Rc thread , Mpa Gauge) Next-generation regulator. Direct drive, pressure regulation system, internal pilot type. Improved flow rate characteristics allow a smaller configuration (close side-by-side spacing possible). Improved operation and maintenance. RZ Regulator RC Thread Mpa Gauge RZ Regulator RC Thread Mpa Gauge Compact design with convenient built-in quick fitting. With pressure gauge for simple pressure checks. Regulator with quick fitting RTS Regulator with quick fitting RTS Instant response, even when there change in the secondary side pressure is great. Uses an air pilot system. High-relief Regulators HR High-relief Regulators HR Large FRL Series regulator. Large FRL series Regulators RN650-902 Large FRL series Regulators RN650-902 (NPT thread , psi Gauge) Next-generation regulator. Direct drive, pressure regulation system, internal pilot type. Improved flow rate characteristics allow a smaller configuration (close side-by-side spacing possible). Improved operation and maintenance. RZ Regulator NPT Thread Psi Gauge RZ Regulator NPT Thread Psi Gauge New Regulators with Quick Fittings are available! RTLP Regulators with Quick Fittings Push Lock type RTLP Regulators with Quick Fittings Push Lock type RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Clean System equipment Cylinder Pen cylinder PBDA (clean equipment) Double acting type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Clean room specification pen cylinder. Single acting push out type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Next SIMILAR PRODUCTS Cylinder Clean System equipment Φ12 to 20 mm [0.472 to 0.787 in] cylinder bore size. Clean room specification mini guide slider. Table type linear guide specifications meet a wide range of needs. Clean room mini guide slider CS-MGA series (Clean system cylinder) Clean room mini guide slider CS-MGA series (Clean system cylinder) Rack-and-pinion type clean room specification rotary actuator. Piston type RAP (clean equipment) Piston type RAP (clean equipment) Φ14 to 56 mm [0.551 to 2.205 in] cylinder bore. Magnet type rodless cylinder with clean room specification. Unique oval barrel design enables low-speed performance, low center of gravity, and non-rotation. Flat rodless MRV (clean equipment) Flat rodless MRV (clean equipment) Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. Clean room jig cylinder with guide. With rolling guide for wide ranging applicability. Jig cylinder with guides (clean equipment Jig cylinder with guides (clean equipment Φ6 to 40 [0.236 to 1.575] cylinder bore. Jig cylinder C Series with low friction clean room specification. Provides both low pressure (0.01 to 0.1 MPa [1.45 to 14.5 psi] minimum working pressure) and low speed operation. Jig cylinder low-friction specification CDAZ (clean equipment) Jig cylinder low-friction specification CDAZ (clean equipment) Φ8 to 40 mm [0.315 to 1.575 in]cylinder bore. Clean equipment dust collection port type and type without dust collection port are available. Positioning pin hole can be selected as an option. Basic cylinders: With guide BCG (clean equipment) Basic cylinders: With guide BCG (clean equipment) Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. A square and compact body, and mounting brackets provides plenty of mounting versatility. Multi mount cylinders (clean equipment) Multi mount cylinders (clean equipment) Φ4.5 to 10 [0.177 to 0.394] cylinder bore. Approximately 41% shorter length, 67% smaller volume. (Compared with Koganei multi mount cylinders.) Mini bit cylinder MBDA (clean equipment) Mini bit cylinder MBDA (clean equipment) Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Twin rod cylinder clean room specification. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Twin rod cylinder TBDA (clean equipment) Twin rod cylinder TBDA (clean equipment) Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Air hand with linear guide, clean room specification. Parallel type NHBDPG (clean equipment) with linear guide Parallel type NHBDPG (clean equipment) with linear guide Φ6 mm [0.236 in] cylinder bore. Clean room specification twin rod cylinder. Twin rod cylinder TDA (clean equipment) Twin rod cylinder TDA (clean equipment) Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Clean room specification slim cylinder. A lineup including double acting type, double rod type, double acting type with end keep, double acting type with block, and double acting type with block and end keep. Slim cylinders (clean equipment) Slim cylinders (clean equipment) Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Jig cylinder C Series clean room specification with short, thin body designed for space saving. A wide range of functions respond to various different needs. Jig cylinder C series (clean equipment) Jig cylinder C series (clean equipment) Φ6 to 125 mm [0.236 to 4.921 in] cylinder bore. Clean equipment dust collection port type and type without dust collection port are available. A new cylinder with direct mounting for minimal size, minimal weight, and space saving. Double acting type basic cylinders BC (clean equipment) Double acting type basic cylinders BC (clean equipment) Double acting type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Clean room specification pen cylinder. Single acting push out type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Pen cylinder PBDA (clean equipment) Pen cylinder PBDA (clean equipment) RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Clean System equipment Cylinder Slim cylinders (clean equipment) Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Clean room specification slim cylinder. A lineup including double acting type, double rod type, double acting type with end keep, double acting type with block, and double acting type with block and end keep. Next SIMILAR PRODUCTS Cylinder Clean System equipment Φ12 to 20 mm [0.472 to 0.787 in] cylinder bore size. Clean room specification mini guide slider. Table type linear guide specifications meet a wide range of needs. Clean room mini guide slider CS-MGA series (Clean system cylinder) Clean room mini guide slider CS-MGA series (Clean system cylinder) Rack-and-pinion type clean room specification rotary actuator. Piston type RAP (clean equipment) Piston type RAP (clean equipment) Φ14 to 56 mm [0.551 to 2.205 in] cylinder bore. Magnet type rodless cylinder with clean room specification. Unique oval barrel design enables low-speed performance, low center of gravity, and non-rotation. Flat rodless MRV (clean equipment) Flat rodless MRV (clean equipment) Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. Clean room jig cylinder with guide. With rolling guide for wide ranging applicability. Jig cylinder with guides (clean equipment Jig cylinder with guides (clean equipment Φ6 to 40 [0.236 to 1.575] cylinder bore. Jig cylinder C Series with low friction clean room specification. Provides both low pressure (0.01 to 0.1 MPa [1.45 to 14.5 psi] minimum working pressure) and low speed operation. Jig cylinder low-friction specification CDAZ (clean equipment) Jig cylinder low-friction specification CDAZ (clean equipment) Φ8 to 40 mm [0.315 to 1.575 in]cylinder bore. Clean equipment dust collection port type and type without dust collection port are available. Positioning pin hole can be selected as an option. Basic cylinders: With guide BCG (clean equipment) Basic cylinders: With guide BCG (clean equipment) Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. A square and compact body, and mounting brackets provides plenty of mounting versatility. Multi mount cylinders (clean equipment) Multi mount cylinders (clean equipment) Φ4.5 to 10 [0.177 to 0.394] cylinder bore. Approximately 41% shorter length, 67% smaller volume. (Compared with Koganei multi mount cylinders.) Mini bit cylinder MBDA (clean equipment) Mini bit cylinder MBDA (clean equipment) Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Twin rod cylinder clean room specification. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Twin rod cylinder TBDA (clean equipment) Twin rod cylinder TBDA (clean equipment) Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Air hand with linear guide, clean room specification. Parallel type NHBDPG (clean equipment) with linear guide Parallel type NHBDPG (clean equipment) with linear guide Φ6 mm [0.236 in] cylinder bore. Clean room specification twin rod cylinder. Twin rod cylinder TDA (clean equipment) Twin rod cylinder TDA (clean equipment) Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Clean room specification slim cylinder. A lineup including double acting type, double rod type, double acting type with end keep, double acting type with block, and double acting type with block and end keep. Slim cylinders (clean equipment) Slim cylinders (clean equipment) Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Jig cylinder C Series clean room specification with short, thin body designed for space saving. A wide range of functions respond to various different needs. Jig cylinder C series (clean equipment) Jig cylinder C series (clean equipment) Φ6 to 125 mm [0.236 to 4.921 in] cylinder bore. Clean equipment dust collection port type and type without dust collection port are available. A new cylinder with direct mounting for minimal size, minimal weight, and space saving. Double acting type basic cylinders BC (clean equipment) Double acting type basic cylinders BC (clean equipment) Double acting type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Clean room specification pen cylinder. Single acting push out type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Pen cylinder PBDA (clean equipment) Pen cylinder PBDA (clean equipment) RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Standard type Cylinder KSD Cylinder Double acting type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong double acting type cylinder that meets JIS standards. Double rod type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. Double acting type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Double acting type, steel tube specification. Double rod type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Steel tubing Φ180 to 250 mm [7.087 to 9.843 in] cylinder bore. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. Next SIMILAR PRODUCTS Cylinder Standard type Φ 20 to 40 mm [0.787 to 1.575 in] cylinder bore. Integrated solenoid valve and cylinder for less wasted air consumption within piping and reduced piping work requirements. DV - Valpack Double Acting Type Slim Cylinder DV - Valpack Double Acting Type Slim Cylinder BDAV Series Φ10 to 16 mm [0.394 to 0.630 in] cylinder bore size. Integration of a vacuum pad and cylinder into a single unit and a hollow shaft structure enables a very small overall length and small operation that fully meets a variety of vacuum system suction and handling, and other needs. Vacuum Pad with Multi mount Cylinders Vacuum Pad with Multi mount Cylinders Double acting type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong double acting type cylinder that meets JIS standards. Double rod type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. Double acting type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Double acting type, steel tube specification. Double rod type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Steel tubing Φ180 to 250 mm [7.087 to 9.843 in] cylinder bore. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. KSD Cylinder KSD Cylinder TDA6 Single acting push out type Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Single acting type with integrated return spring. Double acting long bushing type Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. End keep double acting type Φ16 to 25 mm [0.630 to 0.984 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Twin Rod TDA6 Series Twin Rod TDA6 Series Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. A square and compact body, and mounting brackets provides plenty of mounting versatility. Non-rotating type meets a wide variety of high non-rotating accuracy needs. Multi Mount Cylinders BDA series Multi Mount Cylinders BDA series Knock cylinders NDA series Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Double acting type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Short body and versatile mounting creates a simpler mechanical device. Single acting push out type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Single acting type with integrated return spring. Integrated spanner flats enable secure mounting. Knock Cylinders NDA series Knock Cylinders NDA series Φ2.5 to 16 mm [0.098 to 0.630 in] cylinder bore. Complies with all model non-ion standards. A total of 17 variations, from single and double acting types, to types with stroke adjustment mechanisms. Pen Cylinder PBDA Series Pen Cylinder PBDA Series TBDA - Double acting type Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Twin Rod TBDA (Standard type) Twin Rod TBDA (Standard type) Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. In a single action, the rod moves forward while simultaneously rotating 90 degrees. Slim body and one-location piping ports for a space saving design. Twist Cylinder RHDA Series Twist Cylinder RHDA Series DDA - Double acting type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. A wide range of series configurations and mountings that meet ISO standards make this the standard for tie rod medium-size cylinders. Double acting double rod type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. Conforms to ISO standards. Cylinder with piston rods on both ends of the piston. Double acting multi position type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be linked in series and three stop positions can be specified. Double acting push stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Double acting type Φ32 to 100 mm [1.260 to 3.937 in] cylinder bore. Conforms to ISO standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. End keep double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Non-rotating double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Hexagon type non-rotating piston rod. Non-rotating double acting double rod type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with non-rotating hexagon type piston rod and piston rods at both ends of the piston. Dual stroke double acting pull type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be combined back-to-back for two operation strokes. Double acting pull stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. Valpack double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Integrated solenoid valve and cylinder for less wasted air consumption within piping and reduced piping work requirements. Double acting brake type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with brake mechanism to maintain intermediate stop and position. DYNA Cylinders DYNA Cylinders Φ6 to 20 mm [0.236 to 0.787 in] cylinder bore. Square body and six-side mounting enable compact and direct mounting. High Multi Cylinders YMDA series High Multi Cylinders YMDA series Φ4.5 to 10 [0.177 to 0.394] cylinder bore. Approximately 41% shorter length, 67% smaller volume. (Compared with Koganei multi mount cylinders.) Mini Bit Cylinders MBDA series Mini Bit Cylinders MBDA series Jig cylinder CDA series ● Φ6 to 100 mm [0.236 to 3.937 in] cylinder bore. Short, thin body designed for total space saving. Extensive lineup includes a total of 15 variations. Jig cylinder C series stroke adjustment type ● Φ12 to 40 mm [0.472 to 1.575 in] cylinder bore size. The world's first stroke adjustment cylinder, the push side stroke can be adjusted by rotating the adjuster gear. Jig cylinder C series low-friction cylinders ● Φ6 to 40 mm [0.236 to 1.575 in] cylinder bore. A low friction cylinder with a short, thin body designed for total space saving. Jig Cylinder CDA Double Acting Type Jig Cylinder CDA Double Acting Type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. Stainless steel tubing for high quality and high reliability that sets the standard for small and medium size cylinders. Extensive lineup includes a total of 21 variations. Slim Cylinder DA Series Slim Cylinder DA Series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Fitting Speed controller, fittings, tubes, etc. φ2 Tube Fittings ● Mini type quick fittings ● Speed controllers with quick fittings ● TAC fittings ● Urethane tubes Next SIMILAR PRODUCTS Speed controller, fittings, tubes, etc. Fitting ● Mini type quick fittings ● Speed controllers with quick fittings ● TAC fittings ● Urethane tubes φ2 Tube Fittings φ2 Tube Fittings RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Low speed cylinder Cylinder Slim cylinders (low speed specification) -Double acting type: ● Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. -Double acting block type: ● Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore Next SIMILAR PRODUCTS Cylinder Low speed cylinder Φ6 to 32 mm [0.236 to 1.260 in] cylinder bore. Perfect for slow, smooth low-speed transport. External dimensions of each cylinder are the same as standard products. Twin rod cylinders (low speed specification) Twin rod cylinders (low speed specification) Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Perfect for slow, smooth low-speed transport. External dimensions of each cylinder are the same as standard products. Pen cylinder (low speed specification) Pen cylinder (low speed specification) Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. Perfect for slow, smooth low-speed transport. External dimensions of each cylinder are the same as standard products. Jig cylinder with guides (low speed specification) Jig cylinder with guides (low speed specification) Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. Perfect for slow, smooth low-speed transport. External dimensions of each cylinder are the same as standard products. Jig cylinder C series (low-speed specification) Jig cylinder C series (low-speed specification) Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Perfect for slow, smooth low-speed transport. External dimensions of each cylinder are the same as standard products. Multi mount cylinder (low speed specification) Multi mount cylinder (low speed specification) -Double acting type: ● Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. -Double acting block type: ● Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore Slim cylinders (low speed specification) Slim cylinders (low speed specification) Φ6 to 10 mm [0.236 to 0.394 in] cylinder bore. Perfect for slow, smooth low-speed transport. External dimensions of each cylinder are the same as standard products. Jig cylinder with guides φ6,8.10 (low speed specification) Jig cylinder with guides φ6,8.10 (low speed specification) RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Mounting Brackets Air Filters / Regulators Large FRL series module adapters 8-65_90 Adapter linked to the large FRL multi series. Next SIMILAR PRODUCTS Air Filters / Regulators Mounting Brackets (Psi Gauge) Pressure switch module for FRZ and FRZB Series. Note: Cannot be used in combination with the FRZ Series FRZ3_ or RZ3_. Switch Modules Psi Gauge FRZ series 8Z_F11 Switch Modules Psi Gauge FRZ series 8Z_F11 Modules for linking with the FRZ Series, FRZB Series, CMZ, iB-Cyclone, and more. Modules and Adapters NPT Thread FRZ series 8Z_F11 Modules and Adapters NPT Thread FRZ series 8Z_F11 Adapter linked to the large FRL multi series. Large FRL series module adapters 8-65_90 Large FRL series module adapters 8-65_90 (Mpa Gauge) Pressure switch module for FRZ and FRZB Series. Note: Cannot be used in combination with the FRZ Series FRZ3_ or RZ3_. Switch Modules Mpa Gauge FRZ series 8Z Switch Modules Mpa Gauge FRZ series 8Z Modules for linking with the FRZ Series, FRZB Series, CMZ, iB-Cyclone, and more. Modules and Adapters RC Thread FRZ series 8Z Modules and Adapters RC Thread FRZ series 8Z Adapter linked to the large FRL multi series Multi series module adapters 8-15_60 Multi series module adapters 8-15_60 RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Others, Desktop type compressors Vacuum equipment, pad, Air Filters / Regulators DPT DPV DPP-AY Desktop type compressors Air compressor that can used anywhere with ease. Compact design fits into an A4-size installation area. Low noise design (55 dB). Lightweight (4.6 kg [10.141 lb]). Next SIMILAR PRODUCTS Vacuum equipment, pad, Air Filters / Regulators Others, Desktop type compressors Air compressor that can used anywhere with ease. Compact design fits into an A4-size installation area. Low noise design (55 dB). Lightweight (4.6 kg [10.141 lb]). DPT DPV DPP-AY Desktop type compressors DPT DPV DPP-AY Desktop type compressors RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Solenoid Valve Internal Pilot Valve Solenoid valve 040 series This product has received an order corresponding to for maintenance . Please contact your nearest sales office for more information . Next SIMILAR PRODUCTS Valve Solenoid Valve Internal Pilot F10M_P - F10 Split Manifold Type Plugin Type ● For cylinder bore sizes of 20 to 40 mm [1.575 to 30150 in]. 10 mm [0.394 in] valve width and wire saving type manifold. Addition of wiring enables simple manifold increase or decrease. F15M_P - F15 Split Manifold Type Plugin Type ● For cylinder bore sizes of 40 to 80 mm [1.575 to 3.150 in]. 15 mm [0.591 in] valve width and wire saving type manifold. Addition of wiring enables simple manifold increase or decrease. F10M_P / F15M_P - Split Manifold Plug in Type - F10, F15 Series F10M_P / F15M_P - Split Manifold Plug in Type - F10, F15 Series Perfect for operation control of small-size actuators with a double acting or single acting cylinder bore sizes of 6 to 20 mm [0.236 to 0.787 in]. 030 / H030 series 030 / H030 series Optimal for cylinder bore sizes from 100 to 180 mm [3.937 to 7.087 in]. Next-generation compact, and thin 5-port solenoid valve with high flow rate. Switchable from double to single (two-position double solenoid specifications only). PA / PB Series PA / PB Series For cylinder bore sizes of 50 to 100 mm [1.969 to 3.937 in]. Perfect for operation control of middle-size actuators. A wide variety of lead wire connections and stacking manifolds. Solenoid valve 240 series Solenoid valve 240 series A versatile series that meets the needs of operation control of 20 to 80 mm [0.787 to 30150 in] diameter cylinders and a wide range of other applications. Solenoid valve 180 series Solenoid valve 180 series An external pilot system for versatile 2 and 3-port valves. Amazing versatility packed into a compact configuration. Solenoid valve 112 series Solenoid valve 112 series A versatile series that meets the needs of operation control of 20 to 40 mm [1.575 to 30150 in] diameter cylinders and a wide range of other applications. Solenoid valve 110 series Solenoid valve 110 series This product has received an order corresponding to for maintenance . Please contact your nearest sales office for more information . Solenoid valve 040 series Solenoid valve 040 series Solenoid valve F10 Series for cylinder bore sizes of 20 to 50 mm [0.787 to 1.969 in]. 10 mm [0.394 in] valve width. World's first valve to be equipped with reducer size fitting. A wide range of manifold specifications to meet user needs. F10 Series F10 Series Perfect for operation control electro-pneumatic relay of 2.5 to 10 mm [0.098 to 0.394 in] diameter single acting cylinders. 10 mm [0.394 in] valve width, 1.7 W low power consumption compact configuration solenoid valve. Solenoid valve 010E1 series Solenoid valve 010E1 series For cylinder bore sizes of 50 to 100 mm [1.969 to 3.937 in]. Perfect for operation control of middle-size actuators. High reliability, even without lubrication. Solenoid valve 300 series Solenoid valve 300 series An external pilot system for versatile 2 and 3-port valves. Amazing versatility packed into a compact configuration. Solenoid valve 182 series Solenoid valve 182 series For cylinder bore sizes up to 40 mm [1.575 in]. 10.5 mm [0.413 in] valve width. Thin, compact configuration. Advances the trend towards space-saving machinery and equipment. A tandem three-port valve that provides a high degree of added value. Solenoid valve JA series Solenoid valve JA series F10, F15, F18 Series. Low current type & single dual use valves offer energy saving and low price. 100+ million cycle life tested and rated directional control valve series that can switch direction of the cylinder ports and from double to single solenoid without any additional parts needed. The Selection Guide provides a summary of the 132 F Series – Indirect Acting Solenoid Valves. The F Series variations include: Direct Wiring, D-Sub, Flat Cable or Serial Communication Inline, Subbase, Mono Block and Split Type Manifold Switchable Output Ports Direct on Valve or Manifold Field Selectable Single or Double Solenoid Operation Available with Two 3-way Valves in One Body RoHS Compliance Solenoid Valve F Series Solenoid Valve F Series For cylinder bore sizes up to 25 mm [0.984 in]. 10 mm [0.394 in] valve width. Low power consumption: 0.55 W standard type, 0.15 W low current type. High-response type is also available to meet a wide range of needs and for professional-level control. EA / EB Series EA / EB Series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue CSAD - Single acting double rod type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Cylinder with piston rods on both ends of the piston. Short, thin body designed for total space saving. Next SIMILAR PRODUCTS Consolidates electrical signals from the end of devices and enables communication with higher-level systems I/O Terminal with EtherNet/IP or EtherCat for Koganei F-series valves I/O Terminal with EtherNet/IP or EtherCat for Koganei F-series valves Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be combined back-to-back for two operation strokes. DDAW - Dual stroke double acting pull type DDAW - Dual stroke double acting pull type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with brake mechanism to maintain intermediate stop and position. DDAR - Double acting brake type DDAR - Double acting brake type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Hexagon type non-rotating piston rod. DDAL - Non-rotating double acting type DDAL - Non-rotating double acting type Φ32 to 100 mm [1.260 to 3.937 in] cylinder bore. Conforms to ISO standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. DDAH - Low hydraulic pressure: Double acting type DDAH - Low hydraulic pressure: Double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with non-rotating hexagon type piston rod and piston rods at both ends of the piston. DDADL - Non-rotating double acting double rod type DDADL - Non-rotating double acting double rod type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. A wide range of series configurations and mountings that meet ISO standards make this the standard for tie rod medium-size cylinders. DDA - Double acting type DDA - Double acting type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Short, thin body designed for total space saving. CCDA - Double acting long stroke type CCDA - Double acting long stroke type Φ6 to 50 mm [0.236 to 1.969 in] cylinder bore. Single acting type with integrated return spring. Short, thin body designed for total space saving. CTA - Single acting pull CTA - Single acting pull Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be linked in series and three stop positions can be specified. Short, thin body designed for total space saving. CSAT - Single acting multi position push out type CSAT - Single acting multi position push out type Φ6 to 50 mm [0.236 to 1.969 in] cylinder bore. Single acting type with integrated return spring. Short, thin body designed for total space saving. CSA - Single acting push out type CSA - Single acting push out type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Two cylinders can be linked in series and three stop positions can be specified. Short, thin body designed for total space saving. CDAT - Double acting multi position type CDAT - Double acting multi position type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Square type non-rotating piston rod with a short, thin body designed for total space saving. CDAL - Square rod double acting type CDAL - Square rod double acting type TDA_ALL - φ6 [0.236] Twin rod cylinder ● Φ6 mm [0.236 in] cylinder bore. Original rotation-less cylinder that integrates two cylinders into a compact configuration. TDA - Twin rod cylinder TDA - Twin rod cylinder Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be linked in series and three stop positions can be specified. DDAT - Double acting multi position type DDAT - Double acting multi position type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. DDAP - Double acting push stroke adjustment type DDAP - Double acting push stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. DDAK - End keep double acting type DDAK - End keep double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. DDAE - Double acting pull stroke adjustment type DDAE - Double acting pull stroke adjustment type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. Conforms to ISO standards. Cylinder with piston rods on both ends of the piston. DDAD - Double acting double rod type DDAD - Double acting double rod type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. CCDAK - End keep double acting type CCDAK - End keep double acting type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CTAW - Dual stroke single acting pull type CTAW - Dual stroke single acting pull type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CSAW - Dual stroke type single acting push type CSAW - Dual stroke type single acting push type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Cylinder with piston rods on both ends of the piston. Short, thin body designed for total space saving. CSAD - Single acting double rod type CSAD - Single acting double rod type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CDAW - Dual stroke double acting pull type CDAW - Dual stroke double acting pull type Φ6 to 10 mm [0.236 to 0.394 in] cylinder bore. Small-diameter cylinder with a guide for non-rotation equipped in the main body. A short, thin body designed for total space saving. CDAL_6_8_10 - Non-rotating double acting type CDAL_6_8_10 - Non-rotating double acting type Φ6 to 100 mm [0.236 to 3.937 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Short, thin body designed for total space saving. CDAD - Double acting double rod type CDAD - Double acting double rod type RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue DABF - Block type heat resistant specification: Double acting type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Fluorine packing enables operating temperatures up to 130 degrees. However, a sensor switch cannot be equipped. Next SIMILAR PRODUCTS Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Does not require a mounting bracket. Square rod makes it non-rotating. DABL - Double acting block Square rod type DABL - Double acting block Square rod type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Block type that does not require a mounting bracket. An integrated air cushion absorbs impact force at the stroke end. DABC - Double acting block with variable cushion type DABC - Double acting block with variable cushion type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. DABK - Double acting block end keep type DABK - Double acting block end keep type JDA --> CDA J jig cylinder JDA J jig cylinder JDA Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Low-speed type with an operating speed range from 10 mm/s [0.394 in/sec]. DABN - Block type low speed specification: Double acting type DABN - Block type low speed specification: Double acting type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Fluorine packing enables operating temperatures up to 130 degrees. However, a sensor switch cannot be equipped. DABF - Block type heat resistant specification: Double acting type DABF - Block type heat resistant specification: Double acting type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. Block type that does not require a mounting bracket. Stainless steel tubing for high quality and high reliability. DAB - Double acting block type DAB - Double acting block type RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

KOGANEI pneumatic solutions including quick fittings, barb fittings, speed controllers, pressure switches, flow rate sensors, throttle valves, tubes, mufflers, and hydraulic conversions. Covering in Singapore, Malaysia, Indonesia, Australia, and New Zealand, Koganei Asia's high-quality components, such as the Smart and Rotary quick fittings, ensure durability, efficiency, and ease of installation for diverse industrial applications. Speed controller, fittings, tubes, etc. Quick fittings Barb fittings Speed controller Quick fittings Speed controller threaded pipe Pressure switches and display devices Flow rate sensor switches Throttle valve Tube Plachain ducts Mufflers Column holders and tubing Hydraulic conversion Hydraulic type high-speed control Clean system Pulse blow unit, air gun iB-Flow TAC fitting (barb) View Barbed compact fitting series to support various types of small equipment. Standard type View A wide range of variations available: speed controller with quick fittings for air cylinder speed control, low-pressure, large flow type, etc. Speed Controller with Dial Adjuster and Push Lock View Reduce man-hours spent on flow settings! Low pressure control type View Low speed type speed controller with quick fitting. Provides easy speed control of low-speed specification air cylinders. Quick fittings Barb fittings Speed controller Tube TAC Fittings (Clean Equipment) View Clean room suitable barbed compact fitting series to support various types of small equipment. Standard type View Clean room suitable quick fitting for simple attachment and detachment. Supply joint View Same inner diameter and low volume as steep pipes used for piping, but requiring half the piping space. Urethane tubes (clean equipment) View Small minimum bend radius for outstanding flexibility, plus outstanding weather resistance and oil resistance. Speed controller with quick fitting (clean equipment) View Clean room suitable speed controller with quick fittings for air cylinder speed control. TSC Series (clean equipment) View Clean room suitable fine speed adjustment of the M5 port cylinder. SCL series (clean equipment) View Clean room suitable fine speed adjustment of the Rc1/8?1/4 port cylinder. TSCO Series (clean equipment) View Clean room suitable fine speed adjustment of the M3 port cylinder. SC series (clean equipment) View Clean room suitable fine speed adjustment of the M5?Rc1/8 port cylinder. KSC series (clean equipment) View Clean room suitable simple flow rate adjustment while maintaining stable flow. Standard type View Quick fitting for simple attachment and detachment, and wide variety of specifications: NCU specification that does not generate copper ions, non-lubricant specification, and stainless steel for metal parts specification. Rotary type View Type with integrated smooth moving bearing that is optimal for swinging and rotation, with quick fittings. Supply joint View Same inner diameter and low volume as steep pipes used for piping, but requiring half the piping space. Smart type View Quick fitting for outstanding operability and durability that provides a more compact configuration while maintaining fitting function. A lineup of smart types. With stop valve View Quick fittings with stop valves Connector fittings View Multiple connectors can be freely combined vertically or horizontally using a connector band. TSCO Series View Fine speed adjustment of the M3 port cylinder. SC series View Fine speed adjustment of M5 and Rc1/8 port cylinders. KSC series View Simple flow rate adjustment while maintaining stable flow. TSC Series View Fine speed adjustment of the M5 port cylinder. SCL series View Fine speed adjustment of the Rc1/8 and 1/4 port cylinders. Multi-Channel Sensor Controller MSU Series View 1 Controller centrally manages any 4 sensors with outputs of 1 to 5V. Digital pressure switchs,GS6 View Small pressure switch with outstanding reliability and response for vacuum and positive pressure. Two-screen, three-color indications for easy operation. Air indicators KIS View Whether or not air is present in the line and equipment operation status is indicated by colors. Clear color switching for indicators for outstanding readability. GS1-50 pressure gauge with built-in switches (mechanical) View Set pressure and working pressure displayed by a single pressure gauge. Panel mounting is also supported for easy centralized control and management from the control panel. Electronic pressure switch PS4 View Small pressure switch with outstanding reliability and response for vacuum and positive pressure. A selection of types for various applications. Separate type multi-channel flow rate sensor controller FSU View Pressure sensor detects workpiece suction that cannot be detected by a pressure sensor. Four-point simultaneous detection by a single controller. Computer connectability. Four micro-pressure compatible type modes. Separate type 1-channel flow rate sensor controller FS1U View Enables the same ease of use as a pressure switch. Two-color indicator for at-a-glance check of workpiece suction. Flow volume sensor detects workpiece suction that cannot be detected by a pressure sensor. Throttle valve View For pneumatic equipment speed control and pneumatic signal control. Power reducer View Provides various types of pressure control of drive equipment intake and exhaust air. Nylon tubes View Outstanding friction resistance, bending fatigue resistance, cold resistance, and weather resistance. Flat tubes (urethane) View Dual-conduit tubing that is ideal when tubing space is limited, with markings to identify tubes when connecting them. Tube holder View Allows simple bundling of tubes. Urethane tubes View Small minimum bend radius for outstanding flexibility, plus outstanding weather resistance and oil resistance. Soft nylon tube View Nylon tubing with outstanding water resistance, weather resistance, and dimensional stability, that is also flexible. Plachain ducts View Tubes and cables are bundled in a smart configuration, which supports quick and easy operation of moving devices. Made of lightweight and highly durable engineering plastic for easy handling. Muffler KM series (plastic) View Compact type that offers outstanding silencing and less exhaust back pressure. Also inhibits invasion of foreign matter via the exhaust port. Muffler KM series (brass) View Compact type that offers outstanding silencing and less exhaust back pressure. Also inhibits invasion of foreign matter via the exhaust port. Holders and column tubes View Stronger and easier to use for reliable support of a wide range of machinery and device designs and assemblies. Air-hydro converter AHC View No hydraulic unit is used, which eliminates pulsating and enables greater speed control accuracy. Air bleeders AHB View Bleeds air bubbles accumulated in the low pressure hydraulic circuit, which enables stable speed control. Hydro-checks HC View Seamless hydraulic control of cylinder speed from high speed to low. Maintenance free and totally sealed to eliminate oil leaks. Enables simple speed adjustment and stable speed control. PAG series View Pulse blow air gun Small-size pulse blow type PAU-05 View Generates pulse air without using electricity! iB-Flow View Enables small bore cylinder speed control and low-speed range control. Precision digital control of micro flow volume from a remote location. Good for such applications as air-operated valve open/close speed control. Measurement and visible representation of cylinder operating time. AHB150-01 AHB150-02 AN6 ATBEW10-8 ATBEW8-6-0 ATBLY10-04 ATBY6-01 ATBY8-03 ATL10-02 ATL10-03 ATL10-04 ATL12-02 ATL12-03 ATL12-04 ATL4-02 ATL4-M5-D ATL6-02 ATL6-M5-D ATL8-01 ATL8-02 ATL8-03 ATS10-01 ATS10-02 ATS10-03 ATS12-03 ATS12-04 ATS6-02 ATS6-03 ATS6-M5-D ATS8-01 ATS8-02 ATS8-03 ATSH4-01-D ATSH4-M5-D ATSH6-M5-D ATSM4-01 ATSM6-01 ATSM8-02 ATT10-03 AUK10 AUKM4-01 BB02-01 BBM5-01 BBM5-M5 BF2BU-M3 BF3.2 BF3.2-M3 BF3.2N BF3BU BF3BU-M3 BF4 BF4BU BF4BU-M3 BF4-M3 BF4N BF4U BF5 BF5N BF5N-01 BF6 BF6N BF6N-01 BF6U-01 CBT CF CS3HB CS-TL6-M5 CS-UBW6-4 CS-UP4 CS-UP6 CS-UY6 CVU10 CVU4 CVU4-D CVU6 CVU8 EF EXF EXF-M3 F10Z-J F10Z-J6 F15Z-J5 F15Z-J6 F-H-FC-1/4 F-H-FE-10- F-H-K-4 F-H-MC-8-2 F-H-MCT-1/ F-H-MCT-6- F-H-ME-12- F-H-ME-6-1 F-H-ME-8-2 F-H-ME-8-3 F-H-PG-1 F-H-PG-3 F-H-U-1/4 F-H-UE-1/4 F-H-UT-1/4 FR300-02-A FVA10-03 FVA6-01 FVA8-01 FVB02-10-2 FVN02-02 FVU10-10 FVU10-10-2 FVU12-12 FVU6-6 FVU6-6-2 FVU8-6 FVU8-8 FVU8-8-2 HSCL1 JSC4-M3A JSMU1/4 KM-10 KPL-8-F KSC11 KSC6 MBF10 NBF3.2 NBF3BU NBF4 NBF4-2BU-H NBF4-3BU-H NBF4BU NBF5 NBF6 NF-M3 NSA10X5 PBF3.2 PBF3BU PBF5 PBF6 PE1/4 PF PF-M3 PFS PFS-M3 PHT08-03-D PL1/4-M5M POC4-M3M PU1/4 PU3/16 PU3/8 PY8-D QE2 RB4A-APT RBF RBFM5-M3 RTL4-01 RTL4-M5-G RTL6-01-G RTL6-02-G RTL6-M5-G RTL8-01 RTLP4-M5-G RTLP6-01-G SBA14-03 SC0 SC0-19W SC0-UL SC10-02-A SC10-03-A SC12-03-B SC12-04-A SC3-M3-MA SC3-M5-MA SC4-01-MA SC4-M3-MA SC4-M3-MB SC4-M5MA SC4-M5-MA SC4-M5-MB SC6-01-A SC6-01-A12 SC6-01-MA SC6-01-MB SC6-02-MA SC6-03-A SC6-M5-MA SC6-M5-MB SC8-01-A SC8-01-B SC8-02A SC8-02-A SC8-02-A-3 SC8-02-B SC8-03-A SC8-03-A-3 SC8-04A SC8-04-A SCC4-M3-A SCC4-M3-B SCC4-M5-A SCC6-01-A SCD4-M5-A SCD6-01-A SCD6-02-A SCD6-03-A SCD6-M5-A SCD6-M5-B SCE-02 SCO-UL SL10-02 SL4-01 SL4-M5 SL8-01 SL8-03 SLH10-02 SLH6-02 SLY8-02 SPD65W SPD-65W SPG14 SSF4-01-A SSF4-M3-A SSF4-M5-A SSF4-M5-A- SSF4-M5-AL SSF4-M5-B SSF6-01-A SSF6-01-B SSF6-02-A SSF6-M5-A SSU10 SSU12 SSU4 SSU4L SSU4M SSU6 SSU6L SSU6M SSU8 SSU-8 SSU8M SSUC3 SSUD4 SSUD6 STQ14-12 SUS303-UL4 SUS303-USD SUS303-UYD SUS304-TS6 TB4-01M TB4-M5M TB6-M5M TBZ4-M5 TCS4-4M TF TH4-3 TH4-4 TH6-3 TH6-4 TJ6-01 TL10-01 TL10-02 TL12-02 TL12-03 TL16-03 TL16-04 TL2-M3M TL3-M5M TL4-01 TL4-01M TL4-02 TL4-M3M TL4-M5 TL4-M5M TL4-M6M TL6-01 TL6-01M TL6-02 TL6-M5M TL6-M6M TL8-01 TL8-02 TL8-03 TL8-03T TLL4-M5M TLL6-01M TLL6-M5M TLL8-01 TLL8-02 TLR12-02 TLR4-01 TLR4-M5 TLR6-01 TLR8-01 TLR8-02 TLRH10-03 TLRH4-01 TLS6-M5 TS10-01 TS10-02 TS10-03 TS12-02 TS12-03 TS3-M3M TS3-M5M TS3-M6M TS4-01 TS4-01M TS4-02 TS4-M3M TS4-M3M-D TS4-M5M TS4-M6M TS6-01 TS6-01M TS6-02 TS6-M5M TS6-M6M TS8-01 TS8-02 TS8-03 TSC TSC0 TSC0-L TSH3-M3M TSH3-M5M TSH4-01M TSH4-M3M TSH4-M5M TSH4-M6M TSH6-01M TSH6-M5M TSH6-M6M TSH8-01 TSK4-M6M TSK6-M8M TSM10-02 TSM4-M5M TSM6-01 TSM6-02 TSM8-01 TSR4-M5 TSR6-01 TSR8-03 TSRH6-01 TSS4-M5 TSS6-01 TSS6-M5 TT4-01M TT4-M5M TT6-01M TT6-M5M TVL12-04 TVL4-01 TVL4-M5 TVL6-M5 TVM-01 TVM-02 TVM-M5 TVS6-01-7W TVU12M TVU12M-300 TVU4 TVU4M TVU6 TVU6M TVU8M U10-B-100 U4-C U4-CB U4-G U4-O U4-R U4-W U4-Y U6-C U6P-B U8-B U8-CB UB4 UB6M UBE6-4 UBE8-4 UED10-8 UED6-4 UED8-4 UED8-6 UEDW10-6 UEDW8-4 UEDW8-6 UEF UEF3.2-M3 UEF3BU-M3 UEF4 UEF4BU UEF4BU-M3 UEF4-M3 UEF4N UEF4U UEF5 UEF5N UEF6 UEF6U UEF-M3 UER2BU-M3 UK4M UK6M UKB6 UKBL4 UKBL6 UKBL8 UL12 UL4M UL6M UL8 ULA10 ULA12 ULA4M ULA6M ULAD6-4M ULAV6M UP10 UP12 UP4 UP6 UP8 UR10-6 UR10-8 UR12-10 UR12-6 UR4-2M UR6-4M UR8-4 UR8-6 URTF US10 US12 US2M US3M US4M US6 US6M US8 USD10-8 USD12-10 "USD12-10 " USD16-12 USD4-3M USD6-4 USD6-4M USD8-6 UT10 "UT10 " UT12 UT4 UT4M UT6 UT6M UT8 UTD10-8 UTD6-4M UTD8-6 UTF UTF3.2-M3 UTF4 UTF4BU UTF4-M3 UTF6 UWD6-4 UWD8-6 UXA6M UY10 UY12 UY3M UY4 UY4M UY6M UY8 UYD10-8 UYD6-4 UYD6-4M UYD8-6 UZ8 KM-31 KM-J10 KM-23 KM-11 KM-2 KM-22 KM-1 KM-05 KM-3 KM-4 KM-03 150-30A KM-06 KM-6 Y024025Mufflerfor HC-3 HC-5 HC3 HC5 PO-408-150-PA-HA PU-202-30 PU-203-30 PU-203-30-PA-HAE PU-203-45 PU-203-45-PB-HA PU-204-38 PU-206-50 PU-306-50-PA-HAE PU-306-50-PA-HB PU-306-50-PB-HA PU-408-100-PB-HA PU-408-50 PUL-203-30 PUL-203-45 PUL-206-38 PUL-206-50 PUL-306-50 PUM-202-HA PUM-202-HAE PUM-202-PA PUM-202-PB PUM-203-HA PUM-203-PB PUM-204-HA PUM-204-PA PUM-204-PB PUM-306-HA PUM-306-HAE PUM-306-HB PUM-306-PA PUM-306-PB DTRY-ADN-S DTRY-ADN-U DTY-ADN-S F-9003-BT-4A-30 F-9003-PFA-10X8-10 F-9003-PFA-10X8-20 F-9003-PFA-12X10-10 F-9003-PFA-12X10-20 F-9003-PFA-13X11-10 F-9003-PFA-14X12-10 F-9003-PFA-15X13-10 F-9003-PFA-3X2-10 F-9003-PFA-4X2-10 F-9003-PFA-6.35X3.96-10 F-9003-PFA-6X4-10 F-9003-PFA-6X4-20 F-9003-PFA-7X5-10 F-9003-PFA-8X6-10 F-9003-PFA-8X6-100 F-9003-PFA-HG-4X3-10 FDH-030-J6 N10-B N10-B-100 N6-B N8-B PHT08-03-D PY8-D SET1/2-100-C SN12-N SN4-N U10-B U10-B-100 U10-BU U10-C U10-C U10-C-100 U10-CB U10-Y U12-B U12-B-100 U12-C-100 U12-Y U2-B U2-B-100 U2-C U3-B U3-C U3-CB U4-B U4-B-100 U4-BU U4-C U4-C-100 U4-CB U4-G U4-O U4-R U4-W U4-W-100 U4-Y U4-Y U6A-B U6-B U6-B U6-B-100 U6-BU U6-C U6-C-100 U6-CB U6-G U6-O U6-R U6-W-100 U6-Y U8-B U8-B-100 U8-BU U8-C U8-C U8-C-100 U8-Y UL03-3B UR8-4 US6M EG110 G1-18D G1-20D G1-40 G3-40 G3-40-F11 G3P-40-S G3S-40 GP1-40 GP3-40 GP-FRZ GS1-50-AL GS1-50-DL GS1-50-DL-37W GS1-50-DL-T GS1-50-DL-T-6W GS610 GS610A GS610-B GS610-P GS620 GS620A GS620A-P GS620-B GS620-B GS620-P GS6-B GS6-P GV-40 GV-40-01 KB100 PG1 PR200-G3PS-B PS310 PS310E-L PS410 PS420 PS420A PSU PSU-D PSU-D-P-3LD PSU-D-P-C-3LD PSU-EM-S PSU-EM-S-31W PSU-M PSU-P-C-3L PAU PAG

Previous View PDF Catalogue Handling products for Robots Cylinder Robot Joint IAI Robot Compatible Specialized robot joint for IAI Robot! Next SIMILAR PRODUCTS Cylinder Handling products for Robots Perfect at absorbing errors for small, lightweight parts! Compliance light compact CPLM Compliance light compact CPLM Specialized robot joint for IAI Robot! Robot Joint IAI Robot Compatible Robot Joint IAI Robot Compatible Lightest in the world. Ideal for tool change of robot tip. D-sub and various connectors can be selected. Auto Hand Changer MJC series Auto Hand Changer MJC series Absorbs the position error of the X/Y axis. Compliance light θ-free (parallel type) CPLG Compliance light θ-free (parallel type) CPLG The swing type corrects positional errors when inserting workpieces and press fitting, and when handling workpieces in the X, Y, Z, θ, and α axes. Compliance light swing type CPL_S Compliance light swing type CPL_S Specialized robot joint for EPSON Robot! Robot Joint EPSON Robot Compatible KRJ EPS Robot Joint EPSON Robot Compatible KRJ EPS Energy saving Once connected, electric current is not required. Easy control Controllable with ON / OFF control. Slim design No interference with peripheral devices. High precision Repeatability is ±0.003 mm [0.0001 in.] Size Variation Maximum payloads at 3 kg [6.615 lb], 10 kg [22.050 lb], 30 kg [66.150 lb] Electric Auto Hand Changer EMJ Series Electric Auto Hand Changer EMJ Series Compliance light parallel type Compliance light swing type The parallel type corrects positional errors when inserting workpieces and press fitting, and when handling workpieces in the X, Y, and θ axes. Compliance light parallel type CPL_F Compliance light parallel type CPL_F RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Air Hands Cylinder 180 Degree Open/Close Type NHBDSLG Φ12 to 20 mm [0.472 to 0.787 in] cylinder bore size. 180 degree open/close type. Employs a thrust bearing for high accuracy and high rigidity. Perfect for workpiece escape. Next SIMILAR PRODUCTS Cylinder Air Hands A hollow body inside donut shaped rubber expands inward to grip and hold the outer circumference of the workpiece over a wide area. Air Picker Gripper Air Picker Gripper Big type with a hollow body inside a rubber cylinder that expands into a donut shape to grip and hold the inner diameter of the workpiece over a wide area. Pick type RBP Pick type RBP Φ12 to 25 mm [0.472 to 0.984 in] cylinder bore size. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Wide type air hand WHDP Wide type air hand WHDP Φ12 to 20 mm [0.472 to 0.787 in] cylinder bore size. 180 degree open/close type. Employs a thrust bearing for high accuracy and high rigidity. Perfect for workpiece escape. 180 Degree Open/Close Type NHBDSLG 180 Degree Open/Close Type NHBDSLG Air drive double acting type Φ16 to 25 mm [0.630 to 0.984 in] cylinder bore. Three-finger hand equipped with a linear guide improves allowable load and moment resistance. A hollow shaft makes this product perfect for building in a cylinder for workpiece removal, etc. Mechanical drive normally close single acting type Three-finger hand equipped with a linear guide improves allowable load and moment resistance. A hollow shaft makes this product perfect for building in a cylinder for workpiece removal, etc. 3 finger hand with linear guide NHE Series 3 finger hand with linear guide NHE Series Double acting synchronous type Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Rack-and-pinion mechanism enables synced left and right lever operation. Linear guide creates an accurate and rigid thin body, while double construction enables high gripping force. Double acting Synchronous type (long type) Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Synchronous long stroke type. Linear guide for high rigidity and a thin body design that is perfect for a wide range of workpiece gripping. Double acting asynchronous type Φ8 to 12 mm [0.315 to 0.472 in] cylinder bore. Levers are individually driven by different bore size cylinders, and the lever with the stronger gripping force becomes the gripping fixed point. Linear guide for high rigidity and thin body design. Flat type air hand AFDPG with linear guide Flat type air hand AFDPG with linear guide Double acting type Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Single acting normally open Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Parallel type NHBDP Parallel type NHBDP Single acting normally closed Air piping is not required, making this perfect in areas where air piping is not possible (on an index table, etc.) Parallel type. Single acting normally open Air piping is not required, making this perfect in areas where air piping is not possible (on an index table, etc.) Two types: parallel type and parallel type linear guide specification. Parallel type NHBMP mechanical hands Parallel type NHBMP mechanical hands Double acting type Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Finger type. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Single acting normally open Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Finger type. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPGY with linear guide Parallel type NHBDPGY with linear guide Double acting type Φ8 to 32 mm [0.315 to 1.26 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Single acting normally open Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPG with linear guide Parallel type NHBDPG with linear guide A hollow body inside donut shaped rubber expands inward to grip and hold the outer circumference of the workpiece over a wide area. Grip type RBG Grip type RBG Equipped with linear guide and can be opened and closed by external operation. Mechanical hand that does not require air piping. Mechanical drive hand with linear guide NHBM Mechanical drive hand with linear guide NHBM Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. With linear guide and cam drive for finger operation that is perpendicular to the cylinder operation axis. Twice the gripping power of previous models. L hand with linear guide NHL1D L hand with linear guide NHL1D Φ12 to 25 mm [0.472 to 0.984 in] cylinder bore size. 180 degree finger type. Perfect for chucking and handling. 180 Degree Open/Close type NHBDSL 180 Degree Open/Close type NHBDSL Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Perfect for high rigidity and high accuracy chucking and handling. 40% lighter, 45% smaller than previous models. Parallel type NHC1 series Parallel type NHC1 series Double acting type Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Single acting normally open Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Swing type NHBDS Swing type NHBDS Double acting type Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Single acting normally open Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Parallel type NHBDPA with cross roller bearing Parallel type NHBDPA with cross roller bearing Double acting type Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Single acting normally open Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPGJ with linear guide Parallel type NHBDPGJ with linear guide Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPGL with linear guide Parallel type NHBDPGL with linear guide RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Others Valves High speed valves K series 2-3-4 ports High-speed 3-, 4-port valves K2, K3, K4 series ● Low power with the world's fastest response. Compact configuration and high-speed response of 1.2 to 4 ms (when ON), which is perfect for high-speed vacuum suction transport. Supports both vacuum and positive pressure. Protective structure IP67 compliant. For high speed sorting and air blow applications. Next SIMILAR PRODUCTS Valves Others High-speed 3-, 4-port valves K2, K3, K4 series ● Low power with the world's fastest response. Compact configuration and high-speed response of 1.2 to 4 ms (when ON), which is perfect for high-speed vacuum suction transport. Supports both vacuum and positive pressure. Protective structure IP67 compliant. For high speed sorting and air blow applications. High speed valves K series 2-3-4 ports High speed valves K series 2-3-4 ports Compact design, positive pressure type and negative pressure type available! SMP Smart Mini Compressor and Vacuum Pump SMP Smart Mini Compressor and Vacuum Pump Non-contact, which avoids denting of and damage to workpieces by the pad. Can also hold porous workpieces and workpieces with some unevenness. NCT Non contact transport equipment NCT Non contact transport equipment Mark-free Non-contact Transfer Components NCTN Series NCTN Mark-Free Non contact Transfer Components NCTN Mark-Free Non contact Transfer Components EVP03 Series. Contributes to carbon neutrality! Vacuum Pump Unit EVP series Vacuum Pump Unit EVP series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018. K3-100SF-24-RS

Previous View PDF Catalogue Standard type Cylinder High Multi Cylinders YMDA series Φ6 to 20 mm [0.236 to 0.787 in] cylinder bore. Square body and six-side mounting enable compact and direct mounting. Next SIMILAR PRODUCTS Cylinder Standard type Φ 20 to 40 mm [0.787 to 1.575 in] cylinder bore. Integrated solenoid valve and cylinder for less wasted air consumption within piping and reduced piping work requirements. DV - Valpack Double Acting Type Slim Cylinder DV - Valpack Double Acting Type Slim Cylinder BDAV Series Φ10 to 16 mm [0.394 to 0.630 in] cylinder bore size. Integration of a vacuum pad and cylinder into a single unit and a hollow shaft structure enables a very small overall length and small operation that fully meets a variety of vacuum system suction and handling, and other needs. Vacuum Pad with Multi mount Cylinders Vacuum Pad with Multi mount Cylinders Double acting type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong double acting type cylinder that meets JIS standards. Double rod type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. Double acting type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Double acting type, steel tube specification. Double rod type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Steel tubing Φ180 to 250 mm [7.087 to 9.843 in] cylinder bore. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. KSD Cylinder KSD Cylinder TDA6 Single acting push out type Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Single acting type with integrated return spring. Double acting long bushing type Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. End keep double acting type Φ16 to 25 mm [0.630 to 0.984 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Twin Rod TDA6 Series Twin Rod TDA6 Series Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. A square and compact body, and mounting brackets provides plenty of mounting versatility. Non-rotating type meets a wide variety of high non-rotating accuracy needs. Multi Mount Cylinders BDA series Multi Mount Cylinders BDA series Knock cylinders NDA series Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Double acting type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Short body and versatile mounting creates a simpler mechanical device. Single acting push out type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Single acting type with integrated return spring. Integrated spanner flats enable secure mounting. Knock Cylinders NDA series Knock Cylinders NDA series Φ2.5 to 16 mm [0.098 to 0.630 in] cylinder bore. Complies with all model non-ion standards. A total of 17 variations, from single and double acting types, to types with stroke adjustment mechanisms. Pen Cylinder PBDA Series Pen Cylinder PBDA Series TBDA - Double acting type Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Twin Rod TBDA (Standard type) Twin Rod TBDA (Standard type) Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. In a single action, the rod moves forward while simultaneously rotating 90 degrees. Slim body and one-location piping ports for a space saving design. Twist Cylinder RHDA Series Twist Cylinder RHDA Series DDA - Double acting type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. A wide range of series configurations and mountings that meet ISO standards make this the standard for tie rod medium-size cylinders. Double acting double rod type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. Conforms to ISO standards. Cylinder with piston rods on both ends of the piston. Double acting multi position type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be linked in series and three stop positions can be specified. Double acting push stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Double acting type Φ32 to 100 mm [1.260 to 3.937 in] cylinder bore. Conforms to ISO standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. End keep double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Non-rotating double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Hexagon type non-rotating piston rod. Non-rotating double acting double rod type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with non-rotating hexagon type piston rod and piston rods at both ends of the piston. Dual stroke double acting pull type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be combined back-to-back for two operation strokes. Double acting pull stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. Valpack double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Integrated solenoid valve and cylinder for less wasted air consumption within piping and reduced piping work requirements. Double acting brake type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with brake mechanism to maintain intermediate stop and position. DYNA Cylinders DYNA Cylinders Φ6 to 20 mm [0.236 to 0.787 in] cylinder bore. Square body and six-side mounting enable compact and direct mounting. High Multi Cylinders YMDA series High Multi Cylinders YMDA series Φ4.5 to 10 [0.177 to 0.394] cylinder bore. Approximately 41% shorter length, 67% smaller volume. (Compared with Koganei multi mount cylinders.) Mini Bit Cylinders MBDA series Mini Bit Cylinders MBDA series Jig cylinder CDA series ● Φ6 to 100 mm [0.236 to 3.937 in] cylinder bore. Short, thin body designed for total space saving. Extensive lineup includes a total of 15 variations. Jig cylinder C series stroke adjustment type ● Φ12 to 40 mm [0.472 to 1.575 in] cylinder bore size. The world's first stroke adjustment cylinder, the push side stroke can be adjusted by rotating the adjuster gear. Jig cylinder C series low-friction cylinders ● Φ6 to 40 mm [0.236 to 1.575 in] cylinder bore. A low friction cylinder with a short, thin body designed for total space saving. Jig Cylinder CDA Double Acting Type Jig Cylinder CDA Double Acting Type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. Stainless steel tubing for high quality and high reliability that sets the standard for small and medium size cylinders. Extensive lineup includes a total of 21 variations. Slim Cylinder DA Series Slim Cylinder DA Series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Air Hands, Handling products for Robots Cylinder Systematic handling module Fixed module SHM11 ● Handling module with standardized functions and a fixed robot hand unit. Shorter design time and lower cost. Swivel module SHM21 ● Handling module with standardized swiveling functions for the robot hand unit. Shorter design time and lower cost. Inversion module SHM31 ● Handling module with standardized inversion functions for the robot hand unit. Shorter design time and lower cost. Shift module SHM41 ● Handling module with standardized shift functions for direct drive for the robot hand unit. Shorter design time and lower cost. Cushion module SHM51 ● Handling module with standardized cushion functions for the robot hand unit. Shorter design time and lower cost. Compliance modules SHM61 ● Handling module with standardized error absorption functions for the robot hand unit. Shorter design time and lower cost. Compliance modules NZ specification SHM62 ● Handling module with standardized error absorption functions for the robot hand unit. Shorter design time and lower cost. Parallel clamp module SHM71 ● Handling module with standardized grasping functions for the robot hand unit. Shorter design time and lower cost. Parallel clamp prong module SHM72 ● Handling module with standardized grasping functions for the robot hand unit. Shorter design time and lower cost. Next SIMILAR PRODUCTS Cylinder Air Hands, Handling products for Robots Compliance modules SHM61J ● Handling module with standardized error absorption functions for the robot hand unit. Shorter design time and lower cost. Compliance modules NZ specification SHM62J ● Handling module with standardized error absorption functions for the robot hand unit. Shorter design time and lower cost. Parallel clamp module SHM73J ● Handling module with standardized grasping functions for the robot hand unit. Shorter design time and lower cost. Systematic handling module micro series Systematic handling module micro series Fixed module SHM11 ● Handling module with standardized functions and a fixed robot hand unit. Shorter design time and lower cost. Swivel module SHM21 ● Handling module with standardized swiveling functions for the robot hand unit. Shorter design time and lower cost. Inversion module SHM31 ● Handling module with standardized inversion functions for the robot hand unit. Shorter design time and lower cost. Shift module SHM41 ● Handling module with standardized shift functions for direct drive for the robot hand unit. Shorter design time and lower cost. Cushion module SHM51 ● Handling module with standardized cushion functions for the robot hand unit. Shorter design time and lower cost. Compliance modules SHM61 ● Handling module with standardized error absorption functions for the robot hand unit. Shorter design time and lower cost. Compliance modules NZ specification SHM62 ● Handling module with standardized error absorption functions for the robot hand unit. Shorter design time and lower cost. Parallel clamp module SHM71 ● Handling module with standardized grasping functions for the robot hand unit. Shorter design time and lower cost. Parallel clamp prong module SHM72 ● Handling module with standardized grasping functions for the robot hand unit. Shorter design time and lower cost. Systematic handling module Systematic handling module RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Solenoid valve iB-ZERO(5-ports), Solenoid Valve Internal Pilot IB iB-ZERO(5-ports) Corresponding to cylinder diameter of 80mm[3.150in]. 5 port manifold solenoid valve, the adoption of the world's first all- resin integrally molded body. Easy assembly of the manifold. Thin and lightweight type. Outstanding cost performance. Next SIMILAR PRODUCTS IB Solenoid valve iB-ZERO(5-ports), Solenoid Valve Internal Pilot Corresponding to cylinder diameter of 80mm[3.150in]. 5 port manifold solenoid valve, the adoption of the world's first all- resin integrally molded body. Easy assembly of the manifold. Thin and lightweight type. Outstanding cost performance. iB-ZERO(5-ports) iB-ZERO(5-ports) RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Solenoid Valve Internal Pilot Valve EA / EB Series For cylinder bore sizes up to 25 mm [0.984 in]. 10 mm [0.394 in] valve width. Low power consumption: 0.55 W standard type, 0.15 W low current type. High-response type is also available to meet a wide range of needs and for professional-level control. Next SIMILAR PRODUCTS Valve Solenoid Valve Internal Pilot F10M_P - F10 Split Manifold Type Plugin Type ● For cylinder bore sizes of 20 to 40 mm [1.575 to 30150 in]. 10 mm [0.394 in] valve width and wire saving type manifold. Addition of wiring enables simple manifold increase or decrease. F15M_P - F15 Split Manifold Type Plugin Type ● For cylinder bore sizes of 40 to 80 mm [1.575 to 3.150 in]. 15 mm [0.591 in] valve width and wire saving type manifold. Addition of wiring enables simple manifold increase or decrease. F10M_P / F15M_P - Split Manifold Plug in Type - F10, F15 Series F10M_P / F15M_P - Split Manifold Plug in Type - F10, F15 Series Perfect for operation control of small-size actuators with a double acting or single acting cylinder bore sizes of 6 to 20 mm [0.236 to 0.787 in]. 030 / H030 series 030 / H030 series Optimal for cylinder bore sizes from 100 to 180 mm [3.937 to 7.087 in]. Next-generation compact, and thin 5-port solenoid valve with high flow rate. Switchable from double to single (two-position double solenoid specifications only). PA / PB Series PA / PB Series For cylinder bore sizes of 50 to 100 mm [1.969 to 3.937 in]. Perfect for operation control of middle-size actuators. A wide variety of lead wire connections and stacking manifolds. Solenoid valve 240 series Solenoid valve 240 series A versatile series that meets the needs of operation control of 20 to 80 mm [0.787 to 30150 in] diameter cylinders and a wide range of other applications. Solenoid valve 180 series Solenoid valve 180 series An external pilot system for versatile 2 and 3-port valves. Amazing versatility packed into a compact configuration. Solenoid valve 112 series Solenoid valve 112 series A versatile series that meets the needs of operation control of 20 to 40 mm [1.575 to 30150 in] diameter cylinders and a wide range of other applications. Solenoid valve 110 series Solenoid valve 110 series This product has received an order corresponding to for maintenance . Please contact your nearest sales office for more information . Solenoid valve 040 series Solenoid valve 040 series Solenoid valve F10 Series for cylinder bore sizes of 20 to 50 mm [0.787 to 1.969 in]. 10 mm [0.394 in] valve width. World's first valve to be equipped with reducer size fitting. A wide range of manifold specifications to meet user needs. F10 Series F10 Series Perfect for operation control electro-pneumatic relay of 2.5 to 10 mm [0.098 to 0.394 in] diameter single acting cylinders. 10 mm [0.394 in] valve width, 1.7 W low power consumption compact configuration solenoid valve. Solenoid valve 010E1 series Solenoid valve 010E1 series For cylinder bore sizes of 50 to 100 mm [1.969 to 3.937 in]. Perfect for operation control of middle-size actuators. High reliability, even without lubrication. Solenoid valve 300 series Solenoid valve 300 series An external pilot system for versatile 2 and 3-port valves. Amazing versatility packed into a compact configuration. Solenoid valve 182 series Solenoid valve 182 series For cylinder bore sizes up to 40 mm [1.575 in]. 10.5 mm [0.413 in] valve width. Thin, compact configuration. Advances the trend towards space-saving machinery and equipment. A tandem three-port valve that provides a high degree of added value. Solenoid valve JA series Solenoid valve JA series F10, F15, F18 Series. Low current type & single dual use valves offer energy saving and low price. 100+ million cycle life tested and rated directional control valve series that can switch direction of the cylinder ports and from double to single solenoid without any additional parts needed. The Selection Guide provides a summary of the 132 F Series – Indirect Acting Solenoid Valves. The F Series variations include: Direct Wiring, D-Sub, Flat Cable or Serial Communication Inline, Subbase, Mono Block and Split Type Manifold Switchable Output Ports Direct on Valve or Manifold Field Selectable Single or Double Solenoid Operation Available with Two 3-way Valves in One Body RoHS Compliance Solenoid Valve F Series Solenoid Valve F Series For cylinder bore sizes up to 25 mm [0.984 in]. 10 mm [0.394 in] valve width. Low power consumption: 0.55 W standard type, 0.15 W low current type. High-response type is also available to meet a wide range of needs and for professional-level control. EA / EB Series EA / EB Series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Mist, Micromist filters Air Filters / Regulators Large FRL series Mist Filters MF800-1000 Large FRL Series mist filter. 0.3 μm element removes dirt and oil. Cartridge type element simplifies maintenance. Next SIMILAR PRODUCTS Air Filters / Regulators Mist, Micromist filters Removal of solids 0.01 μm and greater, and residual oil up to 0.01 wt ppm. Installation at an inlet port where oil must not enter or somewhere past the air dryer removes oil and fine particles. Micro Mist Filter KMF Micro Mist Filter KMF Large FRL Series mist filter. 0.3 μm element removes dirt and oil. Cartridge type element simplifies maintenance. Large FRL series Mist Filters MF800-1000 Large FRL series Mist Filters MF800-1000 0.3 μm element removes dirt and oil. Bowl is one-touch attachable and detachable, and cartridge type element simplifies maintenance. Multi series Mist Filters MF300-600 Multi series Mist Filters MF300-600 (Rc thread) 0.01 μm rated filtration, improved flow rate characteristics enables a more compact design. The filter element condition can be inspected visually, making it easier to see when maintenance is required. MMFZ Micro Oil Mist Filters RC Thread FRZ series MMFZ Micro Oil Mist Filters RC Thread FRZ series (Rc thread) 0.3 μm rated filtration, improved flow rate characteristics enables a more compact design. The filter element condition can be inspected visually, making it easier to see when maintenance is required. MFZ Oil Mist Filters RC Thread FRZ series MFZ Oil Mist Filters RC Thread FRZ series Large FRL Series micro mist filter. 0.01 μm element removes fine dirt and oil particles. Cartridge type element simplifies maintenance. Large FRL series Micro Mist Filters MMF600-800 Large FRL series Micro Mist Filters MMF600-800 0.01 μm element removes fine dirt and oil particles. Bowl is one-touch attachable and detachable. Cartridge type element simplifies maintenance. Multi series Micro Mist Micro Filters MMF150-400 Multi series Micro Mist Micro Filters MMF150-400 (NPT thread) 0.01 μm rated filtration, improved flow rate characteristics enables a more compact design. The filter element condition can be inspected visually, making it easier to see when maintenance is required. MMFZ Micro Oil Mist Filters NPT Thread FRZ series MMFZ Micro Oil Mist Filters NPT Thread FRZ series (NPT thread) 0.3 μm rated filtration, improved flow rate characteristics enables a more compact design. The filter element condition can be inspected visually, making it easier to see when maintenance is required. MFZ Oil Mist Filters NPT Thread FRZ series MFZ Oil Mist Filters NPT Thread FRZ series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue CTAW - Dual stroke single acting pull type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. Next SIMILAR PRODUCTS Consolidates electrical signals from the end of devices and enables communication with higher-level systems I/O Terminal with EtherNet/IP or EtherCat for Koganei F-series valves I/O Terminal with EtherNet/IP or EtherCat for Koganei F-series valves Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be combined back-to-back for two operation strokes. DDAW - Dual stroke double acting pull type DDAW - Dual stroke double acting pull type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with brake mechanism to maintain intermediate stop and position. DDAR - Double acting brake type DDAR - Double acting brake type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Hexagon type non-rotating piston rod. DDAL - Non-rotating double acting type DDAL - Non-rotating double acting type Φ32 to 100 mm [1.260 to 3.937 in] cylinder bore. Conforms to ISO standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. DDAH - Low hydraulic pressure: Double acting type DDAH - Low hydraulic pressure: Double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with non-rotating hexagon type piston rod and piston rods at both ends of the piston. DDADL - Non-rotating double acting double rod type DDADL - Non-rotating double acting double rod type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. A wide range of series configurations and mountings that meet ISO standards make this the standard for tie rod medium-size cylinders. DDA - Double acting type DDA - Double acting type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Short, thin body designed for total space saving. CCDA - Double acting long stroke type CCDA - Double acting long stroke type Φ6 to 50 mm [0.236 to 1.969 in] cylinder bore. Single acting type with integrated return spring. Short, thin body designed for total space saving. CTA - Single acting pull CTA - Single acting pull Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be linked in series and three stop positions can be specified. Short, thin body designed for total space saving. CSAT - Single acting multi position push out type CSAT - Single acting multi position push out type Φ6 to 50 mm [0.236 to 1.969 in] cylinder bore. Single acting type with integrated return spring. Short, thin body designed for total space saving. CSA - Single acting push out type CSA - Single acting push out type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Two cylinders can be linked in series and three stop positions can be specified. Short, thin body designed for total space saving. CDAT - Double acting multi position type CDAT - Double acting multi position type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Square type non-rotating piston rod with a short, thin body designed for total space saving. CDAL - Square rod double acting type CDAL - Square rod double acting type TDA_ALL - φ6 [0.236] Twin rod cylinder ● Φ6 mm [0.236 in] cylinder bore. Original rotation-less cylinder that integrates two cylinders into a compact configuration. TDA - Twin rod cylinder TDA - Twin rod cylinder Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be linked in series and three stop positions can be specified. DDAT - Double acting multi position type DDAT - Double acting multi position type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. DDAP - Double acting push stroke adjustment type DDAP - Double acting push stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. DDAK - End keep double acting type DDAK - End keep double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. DDAE - Double acting pull stroke adjustment type DDAE - Double acting pull stroke adjustment type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. Conforms to ISO standards. Cylinder with piston rods on both ends of the piston. DDAD - Double acting double rod type DDAD - Double acting double rod type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. CCDAK - End keep double acting type CCDAK - End keep double acting type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CTAW - Dual stroke single acting pull type CTAW - Dual stroke single acting pull type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CSAW - Dual stroke type single acting push type CSAW - Dual stroke type single acting push type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Cylinder with piston rods on both ends of the piston. Short, thin body designed for total space saving. CSAD - Single acting double rod type CSAD - Single acting double rod type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CDAW - Dual stroke double acting pull type CDAW - Dual stroke double acting pull type Φ6 to 10 mm [0.236 to 0.394 in] cylinder bore. Small-diameter cylinder with a guide for non-rotation equipped in the main body. A short, thin body designed for total space saving. CDAL_6_8_10 - Non-rotating double acting type CDAL_6_8_10 - Non-rotating double acting type Φ6 to 100 mm [0.236 to 3.937 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Short, thin body designed for total space saving. CDAD - Double acting double rod type CDAD - Double acting double rod type RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue With guides Cylinder Axis cylinder XDA series Double acting bushing type. Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Guides are incorporated into both sides of the cylinder. Bushing type for non-rotating control of ±0.3 degrees or less. Double acting bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Guides are incorporated into both sides of the cylinder. Bearing type for non-rotating control of ±0.1 degrees or less. Double acting long bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Guides are incorporated into both sides of the cylinder. Long bearing type for non-rotating control of ±0.05 degrees or less. Double acting double rod bushing type. Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Bushing type that has non-rotating control of ±0.3 degrees or less. Double acting double rod bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Bearing type that has non-rotating control of ±0.1 degrees or less. Double acting double rod long bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Long bearing type that has non-rotating control of ±0.01 degrees or less. Next SIMILAR PRODUCTS Cylinder With guides Double acting bushing type. Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Guides are incorporated into both sides of the cylinder. Bushing type for non-rotating control of ±0.3 degrees or less. Double acting bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Guides are incorporated into both sides of the cylinder. Bearing type for non-rotating control of ±0.1 degrees or less. Double acting long bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Guides are incorporated into both sides of the cylinder. Long bearing type for non-rotating control of ±0.05 degrees or less. Double acting double rod bushing type. Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Bushing type that has non-rotating control of ±0.3 degrees or less. Double acting double rod bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Bearing type that has non-rotating control of ±0.1 degrees or less. Double acting double rod long bearing type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Long bearing type that has non-rotating control of ±0.01 degrees or less. Axis cylinder XDA series Axis cylinder XDA series Double acting type with guides Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Workpiece table with twin rod cylinder and seven guides for high accuracy, high rigidity, and high output. Shock absorber type with guides Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. A shock absorber at the stroke end absorbs end impact force and allows stroke adjustment. End keep type with guides Φ16 to 25 mm [0.630 to 0.984 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Rod slider ARS series Rod slider ARS series Cylinder sensor compatible type with guides Φ6 to 20 mm [0.236 to 0.787 in] cylinder bore. Linear guide equipped in a square body provides space savings and non-rotating accuracy. High multi cylinders YMDAG series High multi cylinders YMDAG series Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Thin actuator with linear guide. Twin rod for high output. Z sider ZS series Z sider ZS series Double acting type with guides φ6 [0.236], 8 [0.315], 10 [0.394] Φ6 to 10 mm [0.236 to 0.394 in] cylinder bore. Small-diameter (Φ6 [0.236], 8 [0.315], 10 [0.394] mm) lineup of standard jig cylinders with guides. Easy to use, saves space. Stroke adjustment double acting type with guides φ6 [0.236], 8 [0.315], 10 [0.394] Φ6 to 10 mm [0.236 to 0.394 in] cylinder bore. Small-diameter (Φ6 [0.236], 8 [0.315], 10 [0.394] mm) lineup of stroke adjustment type standard jig cylinders with guides. Double acting type with guides Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. Perfect for use as a conveyor line stopper or lifter. A selection of four mounting types to match the mounting environment and two different port location directions. Stroke adjustment double acting type with guides Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. With adjuster mechanism that can be used to limit the output side stroke. Jig cylinder with guide that is now even easier to use. End keep double acting type with guides Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Jig cylinder with guide SGDA series Jig cylinder with guide SGDA series Double acting type Φ4.5 to 32 mm [0.177 to 1.260 in] cylinder bore. Standard setter for table type with compact, high-rigidity linear guide. A wide range of variations enables a greater degree of mechanical design freedom. Side mounted double acting type Φ4.5 to 10 mm [0.177 to 0.394 in] cylinder bore. Side mounting block and short pitch mini guide slider that simplifies installation and piping. Double acting type with side-mounted buffer Φ4.5 to 10 mm [0.177 to 0.394 in] cylinder bore. Side mounting block, and short pitch mini guide slider setting and stroke out end error absorbing buffer. Double acting type with end keep Φ12 to 20 mm [0.472 to 0.787 in] cylinder bore size. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Back side piping specification Φ4.5 to 20 mm [0.177 to 0.787 in] cylinder bore. Equipped with a piping block that allows piping from behind the cylinder. Easy installation in locations where limited space is available. Back side piping specification with buffer Φ4.5 to 20 mm [0.177 to 0.787 in] cylinder bore. Equipped with a piping block that allows piping from behind the cylinder. With a buffer that absorbs error on the stroke out end. Double acting type with stroke adjustment buffer Φ4.5 to 20 mm [0.177 to 0.787 in]cylinder bore. Cylinder with stroke limiting stopper. Simple stroke fine-adjustment upon device startup. Double acting type with output side stroke adjustment buffer Φ4.5 to 20 mm [0.177 to 0.787 in] cylinder bore. Cylinder with stroke limiting stopper. With a buffer that absorbs error on the stroke out end. Double acting type with output side and input side stroke adjustments Φ4.5 to 20 mm [0.177 to 0.787 in] cylinder bore. Cylinder with stroke limiting stopper. Simple stroke fine-adjustment upon device startup. Double acting type with output side and input side stroke adjustment buffers Φ4.5 to 20 mm [0.177 to 0.787 in] cylinder bore. Cylinder with stroke limiting stopper. With a buffer that absorbs error on the stroke out end. Double acting type with buffer Φ4.5 to 20 mm [0.177 to 0.787 in] cylinder bore. With a buffer that absorbs error on the stroke out end. Double acting type with buffer and end keep Φ12 to 20 mm [0.472 to 0.787in] cylinder bore size. Equipped with a piping block that allows piping from behind the cylinder. With a buffer that absorbs error on the stroke out end. Mini guide sliders MGA series Mini guide sliders MGA series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Combination Air Filters / Regulators Multi series Combinations FRL C150-600 FRL_C A lineup of all function needed for air treatment of usage end line. Combination air filter, regulator, and lubricator. Next SIMILAR PRODUCTS Air Filters / Regulators Combination A lineup of all function needed for air treatment of usage end line. Combination air filter, regulator, and lubricator. Large FRL series Combinations CN Large FRL series Combinations CN FRL_C A lineup of all function needed for air treatment of usage end line. Combination air filter, regulator, and lubricator. Multi series Combinations FRL C150-600 Multi series Combinations FRL C150-600 iB-Cyclone+FRZ Series combination that completely eliminates the drain. The perfect choice to reduce your number of assemblies and space requirements CMZ Series CMZ Series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Filter Regulators Air Filters / Regulators Large FRL series Filter regulator CY CZ Combination air filter, regulator, and lubricator for high flow rate. Next SIMILAR PRODUCTS Air Filters / Regulators Filter Regulators Compact, lightweight filter regulator. Quick fitting for simple tube connection to the device. Small FR series Filter regulators FRN Small FR series Filter regulators FRN F.R.L 5 μm air filter and regulator incorporated into a compact configuration. Preset marker pressure gauge equipped as standard. Drain cock with fitting or auto drain cock can be selected. Multi series Filter regulators FR Multi series Filter regulators FR (Rc thread , Mpa Gauge) Filter regulator with simple moisture and fluid removal functions in a compact design. Improved flow volume characteristics allow a more compact configuration. Improved bowl attachment and detachment work. FRZB series RC Thread Mpa Gauge FRZB series RC Thread Mpa Gauge In-line Filters that protect against pneumatic equipment trouble, keep air clean In-Line Filter In-Line Filter Next generation of filter regulator. Ideal for use on pneumatic lines downstream of other moisture and fluid removal units. Elimination of drain function provides greater mounting flexibility. Simple bowl attachment design enables easy removal for filter element replacement. The Selection Guide provides a summary of the 7 different Filter Regulators. The FRZ30 / FRZ40 / FRZ50 Series variations include: High Flow in a Compact Body Size Short Filter Bowl (w/o Drain) Is Ideal for Tight Envelopes Tamper Resistant with Removable Adjustment Knob Complete Air Prep Assembly Capability with Sizes 40 and 50 Pressure Setting Range Window Makes It Easy Ensure Correct Setting RoHS Compliance Operations Filter Regulator Low Pressure Filter Regulator Filter Regulator with Reverse Flow Check FRZ series NPT Thread Psi Gauge FRZ series NPT Thread Psi Gauge Combination air filter, regulator, and lubricator for high flow rate. Large FRL series Filter regulator CY CZ Large FRL series Filter regulator CY CZ (NPT thread , psi Gauge) Filter regulator with simple moisture and fluid removal functions in a compact design. Improved flow volume characteristics allow a more compact configuration. Improved bowl attachment and detachment work. FRZB series NPT Thread Psi Gauge FRZB series NPT Thread Psi Gauge A new countermeasure against condensation in compact cylinders, etc.! Simply insert into piping for an easy condensation countermeasure. Water removal valves MTV series Water removal valves MTV series New-generation filter regulator. Perfect on lines following the removal of moisture and fluids. Elimination of fluid removal function for greater mounting direction freedom. Easy bowl attachment and detachment. FRZ series RC Thread Mpa Gauge FRZ series RC Thread Mpa Gauge RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Air Hands Cylinder Swing type NHBDS Double acting type Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Single acting normally open Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Next SIMILAR PRODUCTS Cylinder Air Hands A hollow body inside donut shaped rubber expands inward to grip and hold the outer circumference of the workpiece over a wide area. Air Picker Gripper Air Picker Gripper Big type with a hollow body inside a rubber cylinder that expands into a donut shape to grip and hold the inner diameter of the workpiece over a wide area. Pick type RBP Pick type RBP Φ12 to 25 mm [0.472 to 0.984 in] cylinder bore size. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Wide type air hand WHDP Wide type air hand WHDP Φ12 to 20 mm [0.472 to 0.787 in] cylinder bore size. 180 degree open/close type. Employs a thrust bearing for high accuracy and high rigidity. Perfect for workpiece escape. 180 Degree Open/Close Type NHBDSLG 180 Degree Open/Close Type NHBDSLG Air drive double acting type Φ16 to 25 mm [0.630 to 0.984 in] cylinder bore. Three-finger hand equipped with a linear guide improves allowable load and moment resistance. A hollow shaft makes this product perfect for building in a cylinder for workpiece removal, etc. Mechanical drive normally close single acting type Three-finger hand equipped with a linear guide improves allowable load and moment resistance. A hollow shaft makes this product perfect for building in a cylinder for workpiece removal, etc. 3 finger hand with linear guide NHE Series 3 finger hand with linear guide NHE Series Double acting synchronous type Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Rack-and-pinion mechanism enables synced left and right lever operation. Linear guide creates an accurate and rigid thin body, while double construction enables high gripping force. Double acting Synchronous type (long type) Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Synchronous long stroke type. Linear guide for high rigidity and a thin body design that is perfect for a wide range of workpiece gripping. Double acting asynchronous type Φ8 to 12 mm [0.315 to 0.472 in] cylinder bore. Levers are individually driven by different bore size cylinders, and the lever with the stronger gripping force becomes the gripping fixed point. Linear guide for high rigidity and thin body design. Flat type air hand AFDPG with linear guide Flat type air hand AFDPG with linear guide Double acting type Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Single acting normally open Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Parallel type NHBDP Parallel type NHBDP Single acting normally closed Air piping is not required, making this perfect in areas where air piping is not possible (on an index table, etc.) Parallel type. Single acting normally open Air piping is not required, making this perfect in areas where air piping is not possible (on an index table, etc.) Two types: parallel type and parallel type linear guide specification. Parallel type NHBMP mechanical hands Parallel type NHBMP mechanical hands Double acting type Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Finger type. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Single acting normally open Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Finger type. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPGY with linear guide Parallel type NHBDPGY with linear guide Double acting type Φ8 to 32 mm [0.315 to 1.26 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Single acting normally open Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPG with linear guide Parallel type NHBDPG with linear guide A hollow body inside donut shaped rubber expands inward to grip and hold the outer circumference of the workpiece over a wide area. Grip type RBG Grip type RBG Equipped with linear guide and can be opened and closed by external operation. Mechanical hand that does not require air piping. Mechanical drive hand with linear guide NHBM Mechanical drive hand with linear guide NHBM Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. With linear guide and cam drive for finger operation that is perpendicular to the cylinder operation axis. Twice the gripping power of previous models. L hand with linear guide NHL1D L hand with linear guide NHL1D Φ12 to 25 mm [0.472 to 0.984 in] cylinder bore size. 180 degree finger type. Perfect for chucking and handling. 180 Degree Open/Close type NHBDSL 180 Degree Open/Close type NHBDSL Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Perfect for high rigidity and high accuracy chucking and handling. 40% lighter, 45% smaller than previous models. Parallel type NHC1 series Parallel type NHC1 series Double acting type Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Single acting normally open Φ8 to 25 mm [0.315 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Swing type NHBDS Swing type NHBDS Double acting type Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Single acting normally open Φ6 to 25 mm [0.236 to 0.984 in] cylinder bore. Perfect for chucking and handling. Combination with cylinders allows easy robot arm design. Parallel type NHBDPA with cross roller bearing Parallel type NHBDPA with cross roller bearing Double acting type Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Single acting normally open Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPGJ with linear guide Parallel type NHBDPGJ with linear guide Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Linear guide equipped high-rigidity air hand that is perfect for chucking and handling. Parallel type NHBDPGL with linear guide Parallel type NHBDPGL with linear guide RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Clean System equipment Cylinder Multi mount cylinders (clean equipment) Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. A square and compact body, and mounting brackets provides plenty of mounting versatility. Next SIMILAR PRODUCTS Cylinder Clean System equipment Φ12 to 20 mm [0.472 to 0.787 in] cylinder bore size. Clean room specification mini guide slider. Table type linear guide specifications meet a wide range of needs. Clean room mini guide slider CS-MGA series (Clean system cylinder) Clean room mini guide slider CS-MGA series (Clean system cylinder) Rack-and-pinion type clean room specification rotary actuator. Piston type RAP (clean equipment) Piston type RAP (clean equipment) Φ14 to 56 mm [0.551 to 2.205 in] cylinder bore. Magnet type rodless cylinder with clean room specification. Unique oval barrel design enables low-speed performance, low center of gravity, and non-rotation. Flat rodless MRV (clean equipment) Flat rodless MRV (clean equipment) Φ12 to 63 mm [0.472 to 2.480 in] cylinder bore. Clean room jig cylinder with guide. With rolling guide for wide ranging applicability. Jig cylinder with guides (clean equipment Jig cylinder with guides (clean equipment Φ6 to 40 [0.236 to 1.575] cylinder bore. Jig cylinder C Series with low friction clean room specification. Provides both low pressure (0.01 to 0.1 MPa [1.45 to 14.5 psi] minimum working pressure) and low speed operation. Jig cylinder low-friction specification CDAZ (clean equipment) Jig cylinder low-friction specification CDAZ (clean equipment) Φ8 to 40 mm [0.315 to 1.575 in]cylinder bore. Clean equipment dust collection port type and type without dust collection port are available. Positioning pin hole can be selected as an option. Basic cylinders: With guide BCG (clean equipment) Basic cylinders: With guide BCG (clean equipment) Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. A square and compact body, and mounting brackets provides plenty of mounting versatility. Multi mount cylinders (clean equipment) Multi mount cylinders (clean equipment) Φ4.5 to 10 [0.177 to 0.394] cylinder bore. Approximately 41% shorter length, 67% smaller volume. (Compared with Koganei multi mount cylinders.) Mini bit cylinder MBDA (clean equipment) Mini bit cylinder MBDA (clean equipment) Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Twin rod cylinder clean room specification. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Twin rod cylinder TBDA (clean equipment) Twin rod cylinder TBDA (clean equipment) Φ8 to 20 mm [0.315 to 0.787 in] cylinder bore. Air hand with linear guide, clean room specification. Parallel type NHBDPG (clean equipment) with linear guide Parallel type NHBDPG (clean equipment) with linear guide Φ6 mm [0.236 in] cylinder bore. Clean room specification twin rod cylinder. Twin rod cylinder TDA (clean equipment) Twin rod cylinder TDA (clean equipment) Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Clean room specification slim cylinder. A lineup including double acting type, double rod type, double acting type with end keep, double acting type with block, and double acting type with block and end keep. Slim cylinders (clean equipment) Slim cylinders (clean equipment) Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Jig cylinder C Series clean room specification with short, thin body designed for space saving. A wide range of functions respond to various different needs. Jig cylinder C series (clean equipment) Jig cylinder C series (clean equipment) Φ6 to 125 mm [0.236 to 4.921 in] cylinder bore. Clean equipment dust collection port type and type without dust collection port are available. A new cylinder with direct mounting for minimal size, minimal weight, and space saving. Double acting type basic cylinders BC (clean equipment) Double acting type basic cylinders BC (clean equipment) Double acting type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Clean room specification pen cylinder. Single acting push out type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Pen cylinder PBDA (clean equipment) Pen cylinder PBDA (clean equipment) RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Air Filters Air Filters / Regulators Exhaust filters EF Compact type that offers outstanding silencing and less exhaust back pressure. Also inhibits invasion of foreign matter via the exhaust port. Oil removal from exhaust and lower noise. Clean operation promotes a clean environment. Next SIMILAR PRODUCTS Air Filters / Regulators Air Filters Compact, lightweight air filter. Quick fitting for simple tube connection to the device. Small FR series Air Filters FN100 Small FR series Air Filters FN100 Compact, lightweight vacuum filter. Quick fitting for simple tube connection to the device. Small FR series Vacuum Air Filters VFN100 Small FR series Vacuum Air Filters VFN100 5 μm element with little pressure loss. One-touch attachment and detachment, drain cock with fitting, or auto drain cock can be selected as options for the drain bowl. Multi series Air Filters F150-600 Multi series Air Filters F150-600 (Rc thread) A lineup for filtered particle sizes of 5 μm and 40 μm. The filter element condition can be inspected visually, making it easier to see when maintenance is required. FNZ Air Filters RC Thread FRZ Series FNZ Air Filters RC Thread FRZ Series Compact type that offers outstanding silencing and less exhaust back pressure. Also inhibits invasion of foreign matter via the exhaust port. Oil removal from exhaust and lower noise. Clean operation promotes a clean environment. Exhaust filters EF Exhaust filters EF High capacity filter with a process flow rate of 3000 ?/min or 6000 ?/min. Large FRL series Air Filter FN Large FRL series Air Filter FN (NPT thread) A lineup for filtered particle sizes of 5 μm and 40 μm. The filter element condition can be inspected visually, making it easier to see when maintenance is required. FNZ Air Filters NPT Thread FRZ Series FNZ Air Filters NPT Thread FRZ Series RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Manifold Regulators Air Filters / Regulators Multi series Manifold Regulators R300M Single location checking and adjustment of supply air to multiple lines. The flexibility to meet a variety of different needs. Next SIMILAR PRODUCTS Air Filters / Regulators Manifold Regulators MR050, MR502, MR100, MR102 Single location checking and adjustment of supply air to multiple lines. In addition to a new binary relief type, the flexibility to meet a variety of different needs. Manifold Regulators MR050-MR102 Manifold Regulators MR050-MR102 Manifold regulator RN100M For single unit: MRN100-111 Compact, lightweight manifold regulator. Small FR series Manifold Regulators RN100M Small FR series Manifold Regulators RN100M Single location checking and adjustment of supply air to multiple lines. The flexibility to meet a variety of different needs. Multi series Manifold Regulators R300M Multi series Manifold Regulators R300M RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue Filter Regulators Air Filters / Regulators Small FR series Filter regulators FRN Compact, lightweight filter regulator. Quick fitting for simple tube connection to the device. Next SIMILAR PRODUCTS Air Filters / Regulators Filter Regulators Compact, lightweight filter regulator. Quick fitting for simple tube connection to the device. Small FR series Filter regulators FRN Small FR series Filter regulators FRN F.R.L 5 μm air filter and regulator incorporated into a compact configuration. Preset marker pressure gauge equipped as standard. Drain cock with fitting or auto drain cock can be selected. Multi series Filter regulators FR Multi series Filter regulators FR (Rc thread , Mpa Gauge) Filter regulator with simple moisture and fluid removal functions in a compact design. Improved flow volume characteristics allow a more compact configuration. Improved bowl attachment and detachment work. FRZB series RC Thread Mpa Gauge FRZB series RC Thread Mpa Gauge In-line Filters that protect against pneumatic equipment trouble, keep air clean In-Line Filter In-Line Filter Next generation of filter regulator. Ideal for use on pneumatic lines downstream of other moisture and fluid removal units. Elimination of drain function provides greater mounting flexibility. Simple bowl attachment design enables easy removal for filter element replacement. The Selection Guide provides a summary of the 7 different Filter Regulators. The FRZ30 / FRZ40 / FRZ50 Series variations include: High Flow in a Compact Body Size Short Filter Bowl (w/o Drain) Is Ideal for Tight Envelopes Tamper Resistant with Removable Adjustment Knob Complete Air Prep Assembly Capability with Sizes 40 and 50 Pressure Setting Range Window Makes It Easy Ensure Correct Setting RoHS Compliance Operations Filter Regulator Low Pressure Filter Regulator Filter Regulator with Reverse Flow Check FRZ series NPT Thread Psi Gauge FRZ series NPT Thread Psi Gauge Combination air filter, regulator, and lubricator for high flow rate. Large FRL series Filter regulator CY CZ Large FRL series Filter regulator CY CZ (NPT thread , psi Gauge) Filter regulator with simple moisture and fluid removal functions in a compact design. Improved flow volume characteristics allow a more compact configuration. Improved bowl attachment and detachment work. FRZB series NPT Thread Psi Gauge FRZB series NPT Thread Psi Gauge A new countermeasure against condensation in compact cylinders, etc.! Simply insert into piping for an easy condensation countermeasure. Water removal valves MTV series Water removal valves MTV series New-generation filter regulator. Perfect on lines following the removal of moisture and fluids. Elimination of fluid removal function for greater mounting direction freedom. Easy bowl attachment and detachment. FRZ series RC Thread Mpa Gauge FRZ series RC Thread Mpa Gauge RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

Previous View PDF Catalogue DDA - Double acting type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. A wide range of series configurations and mountings that meet ISO standards make this the standard for tie rod medium-size cylinders. Next SIMILAR PRODUCTS Consolidates electrical signals from the end of devices and enables communication with higher-level systems I/O Terminal with EtherNet/IP or EtherCat for Koganei F-series valves I/O Terminal with EtherNet/IP or EtherCat for Koganei F-series valves Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be combined back-to-back for two operation strokes. DDAW - Dual stroke double acting pull type DDAW - Dual stroke double acting pull type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with brake mechanism to maintain intermediate stop and position. DDAR - Double acting brake type DDAR - Double acting brake type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Hexagon type non-rotating piston rod. DDAL - Non-rotating double acting type DDAL - Non-rotating double acting type Φ32 to 100 mm [1.260 to 3.937 in] cylinder bore. Conforms to ISO standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. DDAH - Low hydraulic pressure: Double acting type DDAH - Low hydraulic pressure: Double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with non-rotating hexagon type piston rod and piston rods at both ends of the piston. DDADL - Non-rotating double acting double rod type DDADL - Non-rotating double acting double rod type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. A wide range of series configurations and mountings that meet ISO standards make this the standard for tie rod medium-size cylinders. DDA - Double acting type DDA - Double acting type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Short, thin body designed for total space saving. CCDA - Double acting long stroke type CCDA - Double acting long stroke type Φ6 to 50 mm [0.236 to 1.969 in] cylinder bore. Single acting type with integrated return spring. Short, thin body designed for total space saving. CTA - Single acting pull CTA - Single acting pull Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be linked in series and three stop positions can be specified. Short, thin body designed for total space saving. CSAT - Single acting multi position push out type CSAT - Single acting multi position push out type Φ6 to 50 mm [0.236 to 1.969 in] cylinder bore. Single acting type with integrated return spring. Short, thin body designed for total space saving. CSA - Single acting push out type CSA - Single acting push out type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Two cylinders can be linked in series and three stop positions can be specified. Short, thin body designed for total space saving. CDAT - Double acting multi position type CDAT - Double acting multi position type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Square type non-rotating piston rod with a short, thin body designed for total space saving. CDAL - Square rod double acting type CDAL - Square rod double acting type TDA_ALL - φ6 [0.236] Twin rod cylinder ● Φ6 mm [0.236 in] cylinder bore. Original rotation-less cylinder that integrates two cylinders into a compact configuration. TDA - Twin rod cylinder TDA - Twin rod cylinder Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be linked in series and three stop positions can be specified. DDAT - Double acting multi position type DDAT - Double acting multi position type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. DDAP - Double acting push stroke adjustment type DDAP - Double acting push stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. DDAK - End keep double acting type DDAK - End keep double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. DDAE - Double acting pull stroke adjustment type DDAE - Double acting pull stroke adjustment type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. Conforms to ISO standards. Cylinder with piston rods on both ends of the piston. DDAD - Double acting double rod type DDAD - Double acting double rod type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. CCDAK - End keep double acting type CCDAK - End keep double acting type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CTAW - Dual stroke single acting pull type CTAW - Dual stroke single acting pull type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CSAW - Dual stroke type single acting push type CSAW - Dual stroke type single acting push type Φ12 to 50 mm [0.472 to 1.969 in] cylinder bore size. Cylinder with piston rods on both ends of the piston. Short, thin body designed for total space saving. CSAD - Single acting double rod type CSAD - Single acting double rod type Φ12 to 100 mm [0.472 to 3.937 in] cylinder bore size. Two cylinders can be combined back-to-back for two operation strokes. Designed for total space saving. CDAW - Dual stroke double acting pull type CDAW - Dual stroke double acting pull type Φ6 to 10 mm [0.236 to 0.394 in] cylinder bore. Small-diameter cylinder with a guide for non-rotation equipped in the main body. A short, thin body designed for total space saving. CDAL_6_8_10 - Non-rotating double acting type CDAL_6_8_10 - Non-rotating double acting type Φ6 to 100 mm [0.236 to 3.937 in] cylinder bore. Cylinder with piston rods on both ends of the piston. Short, thin body designed for total space saving. CDAD - Double acting double rod type CDAD - Double acting double rod type RoHS-compliance Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006. On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances. Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.