top of page
Abstract Background
High Multi Cylinders YMDA series

Standard type

Cylinder

High Multi Cylinders YMDA series

Φ6 to 20 mm [0.236 to 0.787 in] cylinder bore. Square body and six-side mounting enable compact and direct mounting.

Cylinder

Standard type

TBDA - Double acting type Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration.

Twin Rod TBDA (Standard type)

Twin Rod TBDA (Standard type)
Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. In a single action, the rod moves forward while simultaneously rotating 90 degrees. Slim body and one-location piping ports for a space saving design.

Twist Cylinder RHDA Series

Twist Cylinder RHDA Series
DDA - Double acting type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. A wide range of series configurations and mountings that meet ISO standards make this the standard for tie rod medium-size cylinders. Double acting double rod type Φ32 to 125 mm [1.260 to 4.921 in] cylinder bore. Conforms to ISO standards. Cylinder with piston rods on both ends of the piston. Double acting multi position type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be linked in series and three stop positions can be specified. Double acting push stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Double acting type Φ32 to 100 mm [1.260 to 3.937 in] cylinder bore. Conforms to ISO standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. End keep double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Non-rotating double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Hexagon type non-rotating piston rod. Non-rotating double acting double rod type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with non-rotating hexagon type piston rod and piston rods at both ends of the piston. Dual stroke double acting pull type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Two cylinders can be combined back-to-back for two operation strokes. Double acting pull stroke adjustment type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with stroke limiting stopper. Valpack double acting type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Integrated solenoid valve and cylinder for less wasted air consumption within piping and reduced piping work requirements. Double acting brake type Φ40 to 100 mm [1.575 to 3.937 in] cylinder bore. Conforms to ISO standards. Cylinder with brake mechanism to maintain intermediate stop and position.

DYNA Cylinders

DYNA Cylinders
Φ6 to 20 mm [0.236 to 0.787 in] cylinder bore. Square body and six-side mounting enable compact and direct mounting.

High Multi Cylinders YMDA series

High Multi Cylinders YMDA series
Φ4.5 to 10 [0.177 to 0.394] cylinder bore. Approximately 41% shorter length, 67% smaller volume. (Compared with Koganei multi mount cylinders.)

Mini Bit Cylinders MBDA series

Mini Bit Cylinders MBDA series
Jig cylinder CDA series ● Φ6 to 100 mm [0.236 to 3.937 in] cylinder bore. Short, thin body designed for total space saving. Extensive lineup includes a total of 15 variations. Jig cylinder C series stroke adjustment type ● Φ12 to 40 mm [0.472 to 1.575 in] cylinder bore size. The world's first stroke adjustment cylinder, the push side stroke can be adjusted by rotating the adjuster gear. Jig cylinder C series low-friction cylinders ● Φ6 to 40 mm [0.236 to 1.575 in] cylinder bore. A low friction cylinder with a short, thin body designed for total space saving.

Jig Cylinder CDA Double Acting Type

Jig Cylinder CDA Double Acting Type
For DAC is Cylinder with variable cushion (Available at φ20~40 only. Standard equipment for φ50 and φ63) Double acting block Square rod type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Does not require a mounting bracket. Square rod makes it non-rotating. ​Double acting block with variable cushion type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Block type that does not require a mounting bracket. An integrated air cushion absorbs impact force at the stroke end. Double acting multi position type Φ20 to 40 mm [0.787 to 1.575 in] cylinder bore. Two cylinders can be linked in series and three stop positions can be specified. Stainless steel tubing for high quality and high reliability. End keep double acting type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Double acting block end keep type Φ16 to 63 mm [0.630 to 2.480 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure. Double acting brake type Φ20 to 40 mm [0.787 to 1.575 in] cylinder bore. Cylinder with brake mechanism to maintain intermediate stop and position. Double acting pull, push stroke adjustment type Φ20 to 40 mm [0.787 to 1.575 in] cylinder bore. Cylinder with stroke limiting stopper. An adjustable type lineup for both pull side and push side. Dual stroke double acting pull type Φ20 to 40 mm [0.787 to 1.575 in] cylinder bore. Two cylinders can be combined back-to-back for two operation strokes. Stainless steel tubing for high quality and high reliability. Low hydraulic pressure: Double acting type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. ​ Valpack double acting type Φ20 to 40 mm [0.787 to 1.575 in] cylinder bore. Integrated solenoid valve and cylinder for less wasted air consumption within piping and reduced piping work requirements. Double acting type heat resistant type Φ20 to 40 mm [0.787 to 1.575 in] cylinder bore. Fluorine packing enables operating temperatures up to 130 degrees. However, a sensor switch cannot be equipped. Double acting low speed type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Low-speed type with an operating speed range from 10 mm/s [0.394 in/sec]. With scraper double acting type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Scraper added to the rod packing prevents entry of outside foreign matter for wider ranging application potential in a variety of environments. Block type heat resistant specification: Double acting type Φ16 to 40 mm [0.630 to 1.575 in] cylinder bore. Fluorine packing enables operating temperatures up to 130 degrees. However, a sensor switch cannot be equipped. Block type low speed specification: Double acting type Φ20 to 63 mm [0.787 to 2.480 in] cylinder bore. Low-speed type with an operating speed range from 10 mm/s [0.394 in/sec]. All stainless steel specification: Double acting type Φ20 to 40 mm [0.787 to 1.575 in] cylinder bore. Stainless steel used for components for improved corrosion resistance.

Slim Cylinder DA Series

Slim Cylinder DA Series
BDAV Series Φ10 to 16 mm [0.394 to 0.630 in] cylinder bore size. Integration of a vacuum pad and cylinder into a single unit and a hollow shaft structure enables a very small overall length and small operation that fully meets a variety of vacuum system suction and handling, and other needs.

Vacuum Pad with Multi mount Cylinders

Vacuum Pad with Multi mount Cylinders
Double acting type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong double acting type cylinder that meets JIS standards. Double rod type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Aluminum tubing Φ125 to 160 mm [4.921 to 6.299 in] cylinder bore size. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure. Double acting type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Double acting type, steel tube specification. Double rod type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with piston rods on both ends of the piston. Multi position: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be linked in series and three stop positions can be specified. Dual stroke type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Two cylinders can be combined back-to-back for two operation strokes. Push stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Pull stroke adjustment type: Steel tubing Φ125 to 250 mm [4.921 to 9.843 in] cylinder bore size. Strong cylinder that meets JIS standards. Cylinder with stroke limiting stopper. Low hydraulic pressure: Steel tubing Φ180 to 250 mm [7.087 to 9.843 in] cylinder bore. Strong cylinder that meets JIS standards. Pneumatic-hydraulic converter can be used for simple low-speed operation control of a cylinder operated by low hydraulic pressure.

KSD Cylinder

KSD Cylinder
TDA6 Single acting push out type Φ10 to 25 mm [0.394 to 0.984 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. Single acting type with integrated return spring. Double acting long bushing type Φ10 to 32 mm [0.394 to 1.260 in] cylinder bore size. Original rotation-less cylinder that integrates two cylinders into a compact configuration. End keep double acting type Φ16 to 25 mm [0.630 to 0.984 in] cylinder bore. A mechanical lock is equipped in the cylinder on the stroke end to keep it from dropping down under its own weight when there is no pressure.

Twin Rod TDA6 Series

Twin Rod TDA6 Series
Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. A square and compact body, and mounting brackets provides plenty of mounting versatility. Non-rotating type meets a wide variety of high non-rotating accuracy needs.

Multi Mount Cylinders BDA series

Multi Mount Cylinders BDA series
Knock cylinders NDA series Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Double acting type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Short body and versatile mounting creates a simpler mechanical device. Single acting push out type ● Φ6 to 16 mm [0.236 to 0.630 in] cylinder bore. Single acting type with integrated return spring. Integrated spanner flats enable secure mounting.

Knock Cylinders NDA series

Knock Cylinders NDA series
Φ2.5 to 16 mm [0.098 to 0.630 in] cylinder bore. Complies with all model non-ion standards. A total of 17 variations, from single and double acting types, to types with stroke adjustment mechanisms.

Pen Cylinder PBDA Series

Pen Cylinder PBDA Series
Herb Plants
Herb Plants

RoHS-compliance

Koganei has finished to comply Koganei brand products to the RoHS directive which regulates 6 substances, and has been attaching the RoHS-compliant identification mark 'E' to shipped products since July 2006.
 

On June 4th 2015, there was a public notification through an official Gazette [EU2015/863] , informing that the target of regulation will be increased to 10 substances.
 

Koganei is preparing to manufacture products which comply to the RoHS (10 substances), and attach a RoHS-compliant identification mark 'G' to compliant products from July 2018.

bottom of page